Pages: 1 [2] 3 4   Go Down
Author Topic: Arduino MEGA Pinout Diagram  (Read 40508 times)
0 Members and 2 Guests are viewing this topic.
0
Offline Offline
Edison Member
*
Karma: 7
Posts: 1235
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Suggestion:

once you are done.. create a post/thread that has all your work collectively posted?


(maybe even a sticky once done?)  smiley-wink

Logged


Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 524
Posts: 26438
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Current totals follow the current allowed by the different ports.

3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
conditions (non-transient), the following must be observed:

ATmega640/1280/2560:
1.)The sum of all IOL, for ports J0-J7, A0-A7, G2 should not exceed 200 mA.
2.)The sum of all IOL, for ports C0-C7, G0-G1, D0-D7, L0-L7 should not exceed 200 mA.
3.)The sum of all IOL, for ports G3-G4, B0-B7, H0-B7 should not exceed 200 mA.
4.)The sum of all IOL, for ports E0-E7, G5 should not exceed 100 mA.
5.)The sum of all IOL, for ports F0-F7, K0-K7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.

That totals 800mA. There is nothing that says if you draw 200mA in one group that you then can't draw it in another.
So this thinking of only 200mA total is nonsense.

Similar numbers apply to the 328 & 1284.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 361
Posts: 17262
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
That totals 800mA. There is nothing that says if you draw 200mA in one group that you then can't draw it in another.
So this thinking of only 200mA total is nonsense.

LOL, we've had this same discussion before.

Quote
There is nothing that says if you draw 200mA in one group that you then can't draw it in another.

There is also nothing stating that you can take the sum, of all those individual port limits, as the maxiumum chip current draw limit. And no where in the datasheet does it state that 800 ma of total current draw is allowed. And of course as I've stated before the absolute maximum section lists the 200 ma figure. Why would they state 200ma there if it only applied to one port? Your assumption, and it is just an assumption, is in error, IMHO.

But that is why I would like others to comment on the subject, as you and I. while still respectful of each other's opinion, have not been able to come to consensus on the matter now or in the past.

Lefty
« Last Edit: February 03, 2013, 09:06:46 pm by retrolefty » Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 524
Posts: 26438
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

They state the Vcc and Gnd PinS are 200mA. Do you suppose they use wimpier wire in a 2560 vs a 328 so that only 200mA is allowed? I think not.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Italy
Offline Offline
Edison Member
*
Karma: 115
Posts: 1132
O ti distingui o ti estingui
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

ATMega 2560 Pinout is on line on first post.
New version of Arduino MEGA.
Logged

Italy
Offline Offline
Edison Member
*
Karma: 115
Posts: 1132
O ti distingui o ti estingui
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Suggestion:

once you are done.. create a post/thread that has all your work collectively posted?


(maybe even a sticky once done?)  smiley-wink


Shortly I make a collection...
...and a big poster  smiley-grin
Logged

Italy
Offline Offline
Edison Member
*
Karma: 115
Posts: 1132
O ti distingui o ti estingui
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Hello!

I Love your work and the help you give us !!! Thank you

May I would suggest to add the PIN numbers as they are printed on the PCB (you did this on the UNO Reference), this would be easier to use if you don´t screw your Arduino to the printout smiley-wink

Thanks in advance

Matthias

Thanks!
As soon as I have some time.
Logged

Leighton Buzzard, UK
Offline Offline
Edison Member
*
Karma: 21
Posts: 1339
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

excellent stuff
well done, sir!
Logged

there are only 10 types of people
them that understands binary
and them that doesn't

Italy
Offline Offline
Edison Member
*
Karma: 115
Posts: 1132
O ti distingui o ti estingui
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

A new version is online.
« Last Edit: February 06, 2013, 03:36:47 am by pighixxx » Logged

San Jose, CA
Offline Offline
Newbie
*
Karma: 0
Posts: 2
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

This is really beautiful work. Thanks for taking time to do this.
Logged

Italy
Offline Offline
Edison Member
*
Karma: 115
Posts: 1132
O ti distingui o ti estingui
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks again!  smiley-mr-green
Logged

0
Offline Offline
Edison Member
*
Karma: 17
Posts: 1413
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Really nice and amazing work ! congrats !

Thank you very much for sharing this.
Logged

* Si preguntas, pon el código de tu programa, hace mucho mas fácil ayudarte. Y me ahorro un mensaje pidiendo que lo hagas.
* Si consigues solucionar tu problema, dedica unos minutos a explicar en tu post como lo conseguiste para beneficio de todos.
* Cambia el 'Subject' de tu hilo y añade 'SOLUCIONADO' cuando hayas llegado a una solución al problema que planteaste.
* Utiliza un 'Subject' para tu hilo que explique de que va el hilo.
Si estas empezando:
* Comienza a usar Arduino
* Guías de iniciación a Arduino
* Ejemplos
* Referencia del Lenguaje
* Conceptos básicos
Guia de usuario de arduino
Tutoriales en Ingles
Si necesitas que alguien te escriba el código: http://www.freelancer.com/  o esta  http://www.guru.com/

Offline Offline
Newbie
*
Karma: 0
Posts: 2
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Nice work! And not only for a beginner  smiley
Logged

Sweden
Offline Offline
Sr. Member
****
Karma: 13
Posts: 257
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Wow, love your work! Printing this out as we speak (as reference when using my home made mega)! Thank you mate!!
Logged

Tucson, AZ
Offline Offline
Sr. Member
****
Karma: 8
Posts: 311
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thank you very much!
Any plans to work on other variants of the Mega2560 such as the Seeeduino Mega that break out the extra pins?
Logged

Pages: 1 [2] 3 4   Go Up
Jump to: