Pages: 1 2 [3]   Go Down
Author Topic: Capacitive Sensor No Output  (Read 2154 times)
0 Members and 1 Guest are viewing this topic.
Singapore
Offline Offline
Newbie
*
Karma: 0
Posts: 21
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

New findings, I tried the dimmerLEB code and tried shorting the pins directly, I do get an output(-1).





Not sure whether this serves any purpose, but other than the "dimmerLED" code, the other 3 codes does not provide an output even with the pin directly shorted.
Logged

UK
Offline Offline
Shannon Member
****
Karma: 223
Posts: 12630
-
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

The site you linked to describes it as a 5V device and the diagrams clearly show a UNO being used, but the sample code refers to a 3.3V Arduino Pro Mini. I wonder whether the supply voltage requirements have changed, and what the actual voltage requirement for your board is?
Logged

I only provide help via the forum - please do not contact me for private consultancy.

Singapore
Offline Offline
Newbie
*
Karma: 0
Posts: 21
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Finally I am getting output now, HazardMinds was right, the A4 and A5 should swap. Took me much time to resolve this minor mistake. -.-"

Really appreciate all the help given!

Btw, for the touchpad, I am able to get reading of the X - Y coordinates as output.

If I wish to use it as a mouse pad, to control the computer mouse, how do I go about doing that so that the computer detect the arduino as a mouse peripheral .
Logged

Singapore
Offline Offline
Newbie
*
Karma: 0
Posts: 21
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

http://arduino.cc/en/Reference/MouseKeyboard

Can Uno perform the above function? It is not listed inside
Logged

Central MN, USA
Offline Offline
Tesla Member
***
Karma: 73
Posts: 7198
Phi_prompt, phi_interfaces, phi-2 shields, phi-panels
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

http://arduino.cc/en/Reference/MouseKeyboard

Can Uno perform the above function? It is not listed inside

No, only leo, due and micro as stated.
Logged


Central MN, USA
Offline Offline
Tesla Member
***
Karma: 73
Posts: 7198
Phi_prompt, phi_interfaces, phi-2 shields, phi-panels
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Finally I am getting output now, HazardMinds was right, the A4 and A5 should swap. Took me much time to resolve this minor mistake. -.-"

Really appreciate all the help given!

Btw, for the touchpad, I am able to get reading of the X - Y coordinates as output.

If I wish to use it as a mouse pad, to control the computer mouse, how do I go about doing that so that the computer detect the arduino as a mouse peripheral .

Strange. Maybe their diagram is wrong. You did it by the diagram but still after swapping scl sda you go data? Anyway, good for you.
Logged


Singapore
Offline Offline
Newbie
*
Karma: 0
Posts: 21
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Yup, I swapped the SCL and SDA, it was later confirmed by seller too. They are going to update the wiki page soon.

Thanks for suggestion!

Now I am thinking how to implement USB-HID to use as mouse.
I would need to come out with a bigger sensor board with multi touch gesture function.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 1
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Good Day All.

Jus got same devise but using Due.
Could anyone tel me which connector to use.
Futher than START dosent go.

Thanks
Logged

Pages: 1 2 [3]   Go Up
Jump to: