Pages: [1]   Go Down
Author Topic: Adafruit wave shield + other questions  (Read 893 times)
0 Members and 1 Guest are viewing this topic.
Brussels, BE
Offline Offline
Jr. Member
**
Karma: 1
Posts: 62
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Hi,

I'm considering buying the Adafruit wave shield for my Arduino alarm clock, but, as a newbie in audio electronics, I have some questions/concerns I'd like to resolve before acquiring one.

Will the shield deliver enough power to my speakers?
The shield is said to deliver enough power for headphone-type speaker. The fact is, I think my speakers are somewhate bigger than this, and should play the audio at a rather strong volume (it's an alarm clock !). My question then is : what happens if I connect my (perhaprs too "big") speakers directly on this shield ? Will they just produce a low-volume sound or/and the shield itself will be in a dangerous condition ?

Now, you will probably ask : "what is the impedance of your speakers?" I don't know! I guess this won't be of much help, but their dimensions are 5cm*11cm (they have been salvaged from an old television). Actually, they are now fully enclosed in the clock's case and will be very difficul to remove, which brings me to my second question.

How to cheaply measure speaker impedance?
Will a simple mesure of resistance and inductance do the trick ? I dont need a precise value, just an order of magnitude in order to make it work (actually, I don't have much equipment at home -but I can borrow some if necessary-).

What can I do if my volume is too low?
If the power delivered by the shield is actually too low, will a simple amplifier like this one solve my problem ? (i guess it depends again of my speaker's impedence)

Thanks for your time.
« Last Edit: April 12, 2013, 08:51:23 am by Mad physicist » Logged


Montreal
Offline Offline
Faraday Member
**
Karma: 27
Posts: 2563
Per aspera ad astra.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

# 1 Depends on "enough", physiological parameter  smiley-cool
#2 You can measure speakers impedance with DMM, same as any regular resistor.
#3 3.7W is quite high power, it's about level in vast majority TV sets (2-3W).
 
Logged

Brussels, BE
Offline Offline
Jr. Member
**
Karma: 1
Posts: 62
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Thank you for your answers.

I don't think I have a specific impedance-meter, but i can measure inductance and resistance. And assuming most of the speaker's impedance will be contained in its inductance, I can compute the impedance manually (2*pi*nu*L + R), right ?
Logged


Montreal
Offline Offline
Faraday Member
**
Karma: 27
Posts: 2563
Per aspera ad astra.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
All you'll measure with the ohmmeter is the coil's resistance, it's a length of fine enameled wire.
Exactly. Speaker's inductive /  mechanical impedance is highly   non-linear over specified frequency range and doesn't have any sense for real world application. Moreover, it's affected by enclosure, so enameled wire resistance is only parameter that important for amplifier selection
Logged

Brussels, BE
Offline Offline
Jr. Member
**
Karma: 1
Posts: 62
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Speaker's inductive /  mechanical impedance is highly non-linear over specified frequency range
Alright ! Ignore my previous post then smiley
Logged


0
Offline Offline
Edison Member
*
Karma: 7
Posts: 1229
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

to driver bigger speakers you may need an amp..

smaller (hobby, non-powered) speakers are fine...


by default the volume on the Waveshield is NOT loud IMHO...

but I read you can hack this by adding a new resistor (or using a different value one in the beginning/during assembly)

search over at adafruit forums to get more details on it. smiley
Logged


Pages: [1]   Go Up
Jump to: