Go Down

Topic: How do you supply an opamp with -12 volts? (Read 1 time) previous topic - next topic

Voidugu

How do you supply a regular opamp (lm324) with -12V if you do not have a center tapped transformer? (ie regular  240 to 12 volt stepdown transformer with a single secondary coil)

Thank you in advance
Regards Voidugu

Grumpy_Mike

Use two power supplies and connect the + of one to the - of the other to form the ground. Then you have the unconnected + of one to be +12V and the unconnected - of the other to give you -12V.

Alternatively use an op amp that can work off a 5V single rail supply.

Voidugu

Should I go for a rail to rail opamp or a single supply one?

Runaway Pancake

"Hello, I must be going..."
"You gotta fight -- for your right -- to party!"
Don't react - Read.
"Who is like unto the beast? who is able to make war with him?"

jackrae

Or use an isolated DC - to - DC module which will operate off 12 volts and give 12 volts out.   You can then connect the 12 v output to the common 0volt line and the output 0v pin will now sit at -12 volts.

If you use a non-isolated version then you must use one which is designed to give -12 volts output.  ie you connect the 0v output pin to the common 0volt line.

Grumpy_Mike


Should I go for a rail to rail opamp or a single supply one?

Those choices are not mutually exclusive.

With a single supply one that works from 5V that is 2.5V per rail as you have to make a signal ground with two 1K resistors in a potential divider. Put a cap 0.1uF across each.
Then it is best to go for a rail to rail one to give you some swing to play with.

Voidugu

Jackrae can you be a bit more explanatory please. I don't seem to understand what you are saying.

Mike thanks for the help man.

Grumpy_Mike

Jackrae is saying that another choice is to use a DC to DC converter. There are lots of them http://uk.farnell.com/dc-dc-converters
Basically there are two sorts.
1) Isolated - where there is no connection between the input voltage and the output voltage. With these you can then connect the +ve output to the -ve input to get your split supply.
2) non isolated - if you tried the above it would short out but you can get voltage mirrors, that is they will output the negitave of what you put in.

DC-DC converters tend to come as small modules and can be expensive.

jackrae

#8
May 12, 2013, 10:35 am Last Edit: May 12, 2013, 10:39 am by jackrae Reason: 1
Not too expensive I hope ?
http://www.ebay.co.uk/itm/12V-to-12V-1W-DC-DC-Converter-isolated-single-output-New-Qty-1-/121013364355?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item1c2cf56683

Data sheet here :  http://www.datasheetcatalog.org/datasheet/candd/NME0515S.pdf

Grumpy_Mike


Voidugu

Thank you very very much for the help people. It turns out that i only need the opamp to swing its output from 0 to +5 volts (no negative voltage involved). Is though the lm324 able to go as low as 0 volts and as high as +5 volts while being connected to +5volts and ground? I guess if not then i would have to raise the 5 volts and supply it with a negative voltage as well, or go for another opamp or implement your suggestions by using a DC to DC converter or a second center tapped transformer.

Grumpy_Mike

Quote
Is though the lm324 able to go as low as 0 volts and as high as +5 volts while being connected to +5volts and ground?

No.
The data sheet says:-
Quote
Large Output Voltage Swing: 0V to VCC -1.5V

so it will only go to 3.5V
Use a MCP602

pito

..google for beyond the rail and rail to rail opamps. There are dozens of such available today. Most work @5V.
No opamp can work rail-rail output, however. Afaik there are always few mVolts (5-100mV) left, based on the load..
Are you going to use it with your RTD sensor?

Voidugu

Yes pito :) I am currently designing the circuit for a temperature controlled soldering station and i want to get everything sorted out. I guess i am going to go with the lm324 since its cheaper. I will get it to swing to +5V by supplying it with more than 7 volts. By the way the lm324 contains 4 opamps. Do you guys know the package if there is one that contains one instead of all 4 opamps?

pito


Go Up