Pages: 1 [2]   Go Down
Author Topic: How to make wall/obstacle avoiding robot with arduino uno atmega 328  (Read 5403 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Newbie
*
Karma: 0
Posts: 11
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

thanks on advice smiley waiting for modified code smiley
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 11
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

I'm try the code in robot. sensor is working (sending distance to serial monitor) well but motors are on same position without turning :/
Logged

the land of sun+snow
Offline Offline
Faraday Member
**
Karma: 158
Posts: 2887
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

As I originally suggested, the best thing to do is learn how to operate the motors separately from the sensors, and the sensors separately from the motors, and after you do that, only then combine the two together.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 11
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

HELP ME PLEASE  !                                                                          HELP ME PLEASE !                                                                       HELP ME PLEASE ![/color][/color]
Logged

the land of sun+snow
Offline Offline
Faraday Member
**
Karma: 158
Posts: 2887
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

What is the problem now?
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 11
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

sensors are working  smiley-neutral and send details to serial monitor.but motors are not working I tried it by even removing sensor but it wasn't work  smiley-sad
Logged

Seattle, WA USA
Offline Offline
Brattain Member
*****
Karma: 601
Posts: 48543
Seattle, WA USA
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
but motors are not working
All we know so far is where one end of each of 4 wires go. Where is the rest of the schematic? Where is the code?

You need to do some stuff yourself.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 11
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

this is the code I used

int ENA=5;//connected to arduino's port 5 (output pwm)
int IN1=2;//connected to arduino's port 2
int IN2=3;//connected to arduino's port 3
int ENB=6;//connected to arduino's port 5 (output pwm)
int IN3=4;//connected to arduino's port 4
int IN4=7;//connected to arduino's port 7

const int trigPin = 13;
const int echoPin = 12;
 
void setup() {
  // initialize serial communication:
  Serial.begin(9600);
}
 
void loop()
{

 analogWrite (ENA,200);//start driving motorA
  analogWrite (ENB,200);//start driving motorB

  // establish variables for duration of the ping,
  // and the distance result in inches and centimeters:
  long duration, inches, cm;
 
  // The sensor is triggered by a HIGH pulse of 10 or more microseconds.
  // Give a short LOW pulse beforehand to ensure a clean HIGH pulse:
  pinMode(trigPin, OUTPUT);
  digitalWrite(trigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(trigPin, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin, LOW);
 
  // Read the signal from the sensor: a HIGH pulse whose
  // duration is the time (in microseconds) from the sending
  // of the ping to the reception of its echo off of an object.
  pinMode(echoPin, INPUT);
  duration = pulseIn(echoPin, HIGH);
 
  // convert the time into a distance
  inches = microsecondsToInches(duration);
  cm = microsecondsToCentimeters(duration);
 
  Serial.print(inches);
  Serial.print("in, ");
  Serial.print(cm);
  Serial.print("cm");
  Serial.println();
 
if ( inches < 10) {
 
 
  analogWrite (ENA,255);//start driving motorA
  analogWrite (ENB,1);//start driving motorB
 
  delay (500);
 
}



}
 
long microsecondsToInches(long microseconds)
{
  // According to Parallax's datasheet for the PING))), there are
  // 73.746 microseconds per inch (i.e. sound travels at 1130 feet per
  // second).  This gives the distance travelled by the ping, outbound
  // and return, so we divide by 2 to get the distance of the obstacle.
  // See: http://www.parallax.com/dl/docs/prod/acc/28015-PING-v1.3.pdf
  return microseconds / 74 / 2;
}
 
long microsecondsToCentimeters(long microseconds)
{
  // The speed of sound is 340 m/s or 29 microseconds per centimeter.
  // The ping travels out and back, so to find the distance of the
  // object we take half of the distance travelled.
  return microseconds / 29 / 2;
}
Logged

Seattle, WA USA
Offline Offline
Brattain Member
*****
Karma: 601
Posts: 48543
Seattle, WA USA
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
this is the code I used
Wonderful. So, now what we know is that you STILL can't post code correctly. Still NOTHING about where the other end of the wires go.

All I can say at this point is good luck.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 11
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

he he don't say so  smiley-cry smiley-cry I'm new to arduino and I like to go throug but I don't know how to do it and no time to learn on this project because it want to be finish before end of this month  smiley-confuse so please help me
about code- the code above is not a my code it's made by person who like to help me on this thread.in beginning I post 2 codes and they separately work well (working motors and sending distance to serial monitor) but I'm in a trouble of adding these 2 codes together  smiley-confuse that's why I'm asking your help... smiley
Logged

the land of sun+snow
Offline Offline
Faraday Member
**
Karma: 158
Posts: 2887
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

he he don't say so  smiley-cry smiley-cry I'm new to arduino and I like to go throug but I don't know how to do it and no time to learn on this project because it want to be finish before end of this month
Yes, we all have this trouble, don't we. No time to learn how to do our own projects, so better to find someone else to do them for us.

You're off to a VERY BAD start here.

You didn't listen to anything I said previously, so I'll just point you back to read those earlier posts, reply #6 and #9. I'm done here, got other things to do, so good luck.
Logged

Pages: 1 [2]   Go Up
Jump to: