Pages: [1]   Go Down
Author Topic: Can I use the Powerpins to power my Arduino?  (Read 10069 times)
0 Members and 1 Guest are viewing this topic.
netherlands
Offline Offline
Newbie
*
Karma: 0
Posts: 16
Arduino and Linux rock
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Hello, everybody

Can I use the VIN and GND powerpins on my Arduino Uno to power my Arduino (with a 6 AA batteryholder)? Otherwise I'll have to buy a 2.1x5.5 mm powerplug and solder this to my batteryholder.

Thanks for any help,

Superpelican  smiley
Logged

superpelican-online.tk

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 331
Posts: 16540
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Yes that will work. Just be sure to measure or careful inspection if no meter for correct polarity before wiring to the Vin and ground pins.

Lefty
Logged

netherlands
Offline Offline
Newbie
*
Karma: 0
Posts: 16
Arduino and Linux rock
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

So, that means that the Powerpins are connected to the Voltage Regulator, so I won't damage my Arduino?
Logged

superpelican-online.tk

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 331
Posts: 16540
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
So, that means that the Powerpins are connected to the Voltage Regulator, so I won't damage my Arduino?

Yes, the Vin wires to the input of the on-board +5vdc voltage regulator, just like the external power connector does. Vin can be used as an output for voltage if using the external power connector, or as an input for voltage as you want to do. Vin must be around +8vdc or higher, but the closer to 8volts the less heat will be generated by the regulator.

Lefty
Logged

Washington
Offline Offline
God Member
*****
Karma: 30
Posts: 780
Firefox & Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Actually it works down to 6.8v until the 5v starts dropping.
Logged

Avoid throwing electronics out as you or someone else might need them for parts or use.
Solid state rectifiers are the only REAL rectifiers.
Resistors for LEDS!

0
Offline Offline
Newbie
*
Karma: 0
Posts: 32
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

If you have a power source that delivers 6V or less you could connect that directly to the 5V pin of the arduino via a 1N400x diode. The diode has a voltage drop of .7V and the atmega can be safely driven with up to 5.5V
« Last Edit: January 19, 2011, 03:03:36 pm by pannen » Logged

netherlands
Offline Offline
Newbie
*
Karma: 0
Posts: 16
Arduino and Linux rock
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

So, @smeezekitty, I can safely power my Arduino with my 6 AA  batteryholder, wich delivers 7.2 V (as I am going to use 1.2 V NiMH rechargeable batteries)?

Thanks for all the help everyone,

Superpelican  smiley
Logged

superpelican-online.tk

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 331
Posts: 16540
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
Actually it works down to 6.8v until the 5v starts dropping.

The issue isn't just the drop out voltage rating of the regulator. The arduino has a auto-voltage detector/selector circuit wired as a opamp comparator. The external voltage input has to be high enough to trigger this selector circuit to select external voltage over USB voltage. There is also a series polarity protection diode between the external voltage connector and the input of the regulator, which drops a little voltage.  There is a critical voltage value which if below that value the voltage selector circuit will not switch to external source.

Lefty
« Last Edit: January 21, 2011, 10:42:14 am by retrolefty » Logged

0
Offline Offline
Newbie
*
Karma: 0
Posts: 32
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

In a battery powered project I'd always go for a way to feed the arduino directly with regulated 5V. The voltage regulator has a pretty bad efficiency.

A switching regulator is the way to go when you don't want to use your precious battery power to heat your arduino.

[edit]
BTW: A cheap way to get a 5V power source are the USB power packs you can buy to charge your phone/mp3player on the go. They contain a lithium battery, a 5V step up regulator and a charging circuit. You can get them for about 10$
[/edit]
« Last Edit: January 21, 2011, 11:01:46 am by pannen » Logged

netherlands
Offline Offline
Newbie
*
Karma: 0
Posts: 16
Arduino and Linux rock
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

So I also can power my Arduino with a 9V battery+clip instead of the 6 AA the same way? Without blowing my Arduino of course!
,

Superpelican  smiley

Logged

superpelican-online.tk

Lancashire, UK
Offline Offline
Edison Member
*
Karma: 8
Posts: 1992
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Yes but be aware a 9v battery has a very limited capacity and won't last very long.
Logged


Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 331
Posts: 16540
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
Yes but be aware a 9v battery has a very limited capacity and won't last very long.

And they are the most expensive battery you could use from a mah capacity point of view. They go for around $2.50 each at my local drug stores.

Lefty
Logged

netherlands
Offline Offline
Newbie
*
Karma: 0
Posts: 16
Arduino and Linux rock
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Yes, I already heard that when you feed your Arduino with a 9V they don't last long. But it is only until I have a 6 AA holder.

Thanks,

Superpelican  smiley
Logged

superpelican-online.tk

Pages: [1]   Go Up
Jump to: