Go Down

Topic: binary output for an R/2R ladder. (Read 2399 times) previous topic - next topic


So, first post. I'm not sure if something like this is posted around here somewhere so here goes.

I'm trying to take an analog input from a pot (0-255) and send that to an 8-bit R/2R ladder connected to the digital pins. I know the easiest way to get the 0-255 value is to use:

map(potin, 0, 1023, 0, 255)

My question is, is there an easier way to do the binary output on the digital pins than using a switch/case with 256 cases?


Coding Badly

The simplest way would be to put all the eight lines of the ladder on a single I/O port (like port C).  You would then be able to output the value with a simple assignment...

 PORTC = MyAnalogValue;

There's a description here that will hopefully get you started...


Good luck,


ah, that is cool. So, something along the lines of:

switch (potin)
  case 1:
  PORTD = B00000000

  case 2:
  PORTD = B00000001


  case 256:
  PORTD = B11111111

would be the way to go? Just want to make sure. I'm new to Arduino but have a basic grasp of C++



No, you're making it too complicated! What Coding Badly was coding properly was much simpler:
Code: [Select]
val = map(potin, 0, 1023, 0, 255);
PORTC = val;

The end. That's it! Assuming, of course, all your pins are on PORTC and you've configured all pins to be outputs.

The bigger question is: why? It sounds like you're trying to "reflect" an analog voltage set by a potentiometer to go somewhere else. Why not just use an op-amp in a noninverting buffer configuration? One little chip...


Ah, that makes a lot more sense. Thank you RuggedCircuits. As to why: It's going to be a part of something bigger. My own take on an Arduino synthesizer. I'll be sure to post results as I go along. Just waiting for my Arduino to arrive in the mail to implement things.



Is there a port that you could actually do this with on a Duemilanove?  PORTD looks like the only one where you might be able to use all 8 pins, but 0 and 1 are the serial Tx/Rx pins, so you might have to connect/disconnect them every time you uploaded a new sketch.

You could also use a shift register chip like a 74HC595 and use shiftOut.  Modified from http://www.arduino.cc/en/Reference/ShiftOut ...
Code: [Select]

//Pin connected to ST_CP of 74HC595
int latchPin = 8;
//Pin connected to SH_CP of 74HC595
int clockPin = 12;
////Pin connected to DS of 74HC595
int dataPin = 11;

////Pin connected to your analog pot
int potPin = 5;

void setup() {
 //set pins to output because they are addressed in the main loop
 pinMode(latchPin, OUTPUT);
 pinMode(potPin, INPUT);

void loop() {
 potin = analogRead(potPin);
 val = map(potin, 0, 1023, 0, 255);

 //ground latchPin and hold low for as long as you are transmitting
 digitalWrite(latchPin, 0);
 shiftOut(dataPin, clockPin, MSBFIRST, val);  
 //return the latch pin high to signal chip that it
 //no longer needs to listen for information
 digitalWrite(latchPin, 1);


If you don't want to use a continuous port and you don't have a shift register chip "handy" you could just define a eight digital pins (I'm using 2 through 9, but you could use others) and use the following code:
Code: [Select]

val = map(potin, 0, 1023, 0, 255);
pin2 = (val&B1?HIGH:LOW);                 // LSB
pin3 = (val&B10?HIGH:LOW);
pin4 = (val&B100?HIGH:LOW);
pin5 = (val&B1000?HIGH:LOW);
pin6 = (val&B10000?HIGH:LOW);
pin7 = (val&B100000?HIGH:LOW);
pin8 = (val&B1000000?HIGH:LOW);
pin9 = (val&B10000000?HIGH:LOW);          // MSB

Go Up

Please enter a valid email to subscribe

Confirm your email address

We need to confirm your email address.
To complete the subscription, please click the link in the email we just sent you.

Thank you for subscribing!

via Egeo 16
Torino, 10131