Pages: [1]   Go Down
Author Topic: Error uploading sketch to Arduino Lilypad PostPosted: Fri Jan 28, 2011 11:15 pm  (Read 4625 times)
0 Members and 1 Guest are viewing this topic.
Portland Oregon
Offline Offline
Newbie
*
Karma: 0
Posts: 46
Blink
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

I just received a new Lilypad and FTDI connector and I can't upload an Arduino sketch to it. I have a Uno and that works fine. I am on OSX 10.6. I have installed the latest FTDI Serial Driver and have the latest Arduino software. I have seen other threads on this but they seem to often end at the bit of advice about selecting the correct board and serial port. I have tried that with no luck. My Uno works great and I am hooked.

When I connect to USB the lilypad lights up. When I try to upload a sketch a red LED lights up for the TX pin.

The Lilypad does not respond to the upload attempt at all.

The Error I am receiving when trying to upload the Blink example to the Lilypad:
Binary sketch size: 1042 bytes (of a 30720 byte maximum)
avrdude: stk500_recv(): programmer is not responding

Arduino Application Version: 0022
Selected Board: Arduino Lilypad ATMega328
Selected Serial: tty.usbserial-A600EHU0

Is there something I am missing? A setting that I am not aware of? I don't think I am running anything on or connected to the mac that would be interfering with the serial port.
Logged

It would probably be safer to play with matches.

---------
Current Project: http://www.fredknack.com/jumpwall/
http://www.jumpwirevideo

Global Moderator
Dallas
Offline Offline
Shannon Member
*****
Karma: 207
Posts: 12904
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Did you change the board setting?
Logged

London, GB
Offline Offline
Sr. Member
****
Karma: 8
Posts: 332
Nothing works.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Which FTDI thing is it?
Logged

Portland Oregon
Offline Offline
Newbie
*
Karma: 0
Posts: 46
Blink
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Which FTDI thing is it?

FTDI Basic Breakout - 5V
http://www.sparkfun.com/products/9716

Thanks
Logged

It would probably be safer to play with matches.

---------
Current Project: http://www.fredknack.com/jumpwall/
http://www.jumpwirevideo

Portland Oregon
Offline Offline
Newbie
*
Karma: 0
Posts: 46
Blink
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Did you change the board setting?


I set the Board Setting ti the Lilypad ATMega 328.
Logged

It would probably be safer to play with matches.

---------
Current Project: http://www.fredknack.com/jumpwall/
http://www.jumpwirevideo

Forum Administrator
Cambridge, MA
Offline Offline
Faraday Member
*****
Karma: 12
Posts: 3538
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Can you provide the verbose output (hold shift while pressing the upload button in the toolbar in the Arduino software)?  Do you have the FTDI cable all the way onto the header pins on the LilyPad?  It's definitely got a 328 on it, right?  Try a different mini USB cable?  If none of that works, you should probably contact SparkFun tech support; it's possible the board is somehow defective (missing bootloader, etc).
Logged

Portland Oregon
Offline Offline
Newbie
*
Karma: 0
Posts: 46
Blink
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks Mellis

Here is the verbose response:

avrdude: stk500_recv(): programmer is not responding
Binary sketch size: 1042 bytes (of a 30720 byte maximum)
/Applications/Arduino.app/Contents/Resources/Java/hardware/tools/avr/bin/avrdude -C/Applications/Arduino.app/Contents/Resources/Java/hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega328p -cstk500v1 -P/dev/tty.usbserial-A600eHU0 -b57600 -D -Uflash:w:/var/folders/LI/LIwoiFgcGTuhyk1xktVSj++++TI/-Tmp-/build4324506453709382490.tmp/Blink.cpp.hex:i

avrdude: Version 5.4-arduino, compiled on Oct  9 2007 at 11:20:31
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         System wide configuration file is "/Applications/Arduino.app/Contents/Resources/Java/hardware/tools/avr/etc/avrdude.conf"
         User configuration file is "/Users/FreddyK/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port            : /dev/tty.usbserial-A600eHU0
         Using Programmer      : stk500v1
         Overriding Baud Rate  : 57600
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: Send: Q [51]   [20]
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
Logged

It would probably be safer to play with matches.

---------
Current Project: http://www.fredknack.com/jumpwall/
http://www.jumpwirevideo

Pages: [1]   Go Up
Jump to: