Pages: [1]   Go Down
Author Topic: 12V GearMotor + Dual Motor Driver TB6612FNG  (Read 1032 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Newbie
*
Karma: 0
Posts: 9
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hello everyone, I'm quite new to the arduino world... I'm currently attempting to set up my gear motor with its driver. To be honest I'm not sure where to start. I have the driver on the breadboard and that's as far as I've gotten. As a baby step... I would just like this motor to start spinning. Please help.

(Later I will be incorporating a photo resistor in order to measure the amount of light/voltage to pass through the motor)

Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 9
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Basically I need some help in order to figure out how to wire this baby. I have all my hardware and programming figured out... however I'm not so great at figuring how to put this all together. No laughing.. once again I'm new at this :\
Logged

Seattle, WA USA
Offline Offline
Brattain Member
*****
Karma: 551
Posts: 46215
Seattle, WA USA
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
Basically I need some help in order to figure out how to wire this baby.
Quote
I have all my hardware and programming figured out.
Sounds like you don't quite have all your hardware figured out.

Now, for my favorite mantra: Post link(s) to the hardware you are trying to use.

Don't make us hunt for what you might or might not have. Without links, we're not as inclined to try to help.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 9
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Thanks for the response smiley I currently have...

Motor: looks a lot like this.. however it only has positive and negative wires... and no decoder. Just a basic dc gear motor. 12v 19:1
http://creatroninc.com/motors/gear-dc-motors/motor-111443.html

Dual Motor Drive TB6612FNG http://www.pololu.com/catalog/product/713

Photo resistor

12v relay

Diode

transistor

Hopefully I have everything I need to get this motor running. (the photo resistor I want to incorporate later on... in order for the motor to  differentiate when to spin according to the amount of light that goes into the resistor )
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 9
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

And of course the basic wires, breadboard and many other little gadgets. A basic outline for a starter would be amazing... to my surprise I can't even find a basic tutorial to get a dc gear motor running with an arduino.
Logged

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 331
Posts: 16540
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

A missing key parameter is how much current the motor will draw at the full mechanical load you will be applying to it. Only then will you know if that motordriver is suitable for your application or not.


Lefty
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 9
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Here is a link with some spec:
http://www.pololu.com/catalog/product/1102

Just found it smiley Hopefully this is helps..
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 9
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Honestly the driver was recommended by the shop owner, it was hard to understand him since he spoke broken english however... from what I understood "this motor will not run without this driver". >.<
Logged

Left Coast, CA (USA)
Offline Offline
Brattain Member
*****
Karma: 331
Posts: 16540
Measurement changes behavior
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Here is a link with some spec:
http://www.pololu.com/catalog/product/1102

Just found it smiley Hopefully this is helps..

The key spec from that link is: "Key specs at 12 V: 500 RPM and 300 mA free-run, 84 oz-in (5 kg-cm) and 5 A stall."

So the motor can draw anywhere between 300ma and 5 amps, depending on the mechanical load you attach to it. The motor driver you selected has a 1 amp continous current spec, so you see the problem here? Unless you know what how much current your application will place on the motor worst case, that motor driver may be underpowered and could be damaged. So unless you can obtain that information you should be using a motor drive capable of supplying worst case stall current for the motor.

Lefty



Logged

Pages: [1]   Go Up
Jump to: