Pages: 1 [2]   Go Down
Author Topic: Arduino Mini 04 with ATmega328  (Read 7979 times)
0 Members and 1 Guest are viewing this topic.
Versailles France
Offline Offline
Newbie
*
Karma: 0
Posts: 2
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hello.
After a lot of spending time, I confirm that it works also for me !!

Thank's a lot FRY!!!! Newbie ..but efficient !!!!

how did you understand the solution of these issue??
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 7
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Same here, works like a charm. you rock dude smiley-wink
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 2
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

FANTASTIC smiley smiley-mr-green smiley-grin

Adding the new board type worked for me.

Thanks for you help.

~Matt
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 3
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

I can't believe they did not publish this change on the site or better update the IDE's files. Only clue was a tiny sticker saying "328" on the mini. But that actually covered the processor so it took me some time to figure out that actually represented the processor type! This cost me half a day of development time...

But thank's a million for the solution or I would still be breaking my head over this.
Logged

0
Offline Offline
Newbie
*
Karma: 0
Posts: 9
Arduino rocks
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hello,


I have the same problem and try use the solution posted, but now i get this;


Binary sketch size: 970 bytes (of a 28672 byte maximum)
C:\Users\Daniel Melo\Documents\Projectos\arduino-0022\hardware/tools/avr/bin/avrdude -CC:\Users\Daniel Melo\Documents\Projectos\arduino-0022\hardware/tools/avr/etc/avrdude.conf -v -v -v -v -patmega328p -cstk500v1 -P\\.\COM13 -b115200 -D -Uflash:w:C:\Users\DANIEL~1\AppData\Local\Temp\build3196484183096855382.tmp\BlinkWithoutDelay.cpp.hex:i

avrdude: Version 5.4-arduino, compiled on Oct 11 2007 at 19:12:32
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         System wide configuration file is "C:\Users\Daniel Melo\Documents\Projectos\arduino-0022\hardware/tools/avr/etc/avrdude.conf"

         Using Port            : \\.\COM13
         Using Programmer      : stk500v1
         Overriding Baud Rate  : 115200
avrdude: ser_open(): setting dtr
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Send: 0 [30]   [20]
avrdude: Recv:
avrdude: stk500_getsync(): not in sync: resp=0x1c
avrdude: Send: Q [51]   [20]
avrdude: Recv:
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x1c

avrdude done.  Thank you.


I´m using a USB 2 Serial Light to upload the Sketch.

Please help.

Thanks
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 1
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

I have the exact same error that daniel_melo is getting.  I updated boards.txt with the new profile.  No luck. FTDI and Arduino IDE are up to date, have power, etc. 

This is such bull.  On the bright side I think this might be the Arduino FAIL that pushes me over the edge.  Time to learn to use PICs instead of wasting time and money on a company that doesn't give a shit.
Logged

Offline Offline
Full Member
***
Karma: 0
Posts: 134
We were born naked, wet and hungry. And then things get worse!!!
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hi,

I am using the same Arduino Mini 04 with Arduino 1.0 IDE . Insted of using a Mini USB adapter, I am using Arduino Duemilanove. The wiring is as follows
http://arduino.cc/en/Guide/ArduinoMini

I get supply to the board, but When I try to upload, I get

Binary sketch size: 1026 bytes (of a 28672 byte maximum)
avrdude: stk500_getsync(): not in sync: resp=0x00

I even tried pressing shift while uploading, I get the same error

Also, As suggested, I copied
Mini with ATmega328

mini328.upload.protocol=stk500
mini328.upload.maximum_size=28672
mini328.upload.speed=115200

mini328.bootloader.low_fuses=0xff
mini328.bootloader.high_fuses=0xd8
mini328.bootloader.extended_fuses=0x05
mini328.bootloader.path=bt
mini328.bootloader.file=ATmegaBOOT_168_atmega328.hex
mini328.bootloader.unlock_bits=0x3F
mini328.bootloader.lock_bits=0x0F

mini328.build.mcu=atmega328p
mini328.build.f_cpu=16000000L
mini328.build.core=arduino

to the boards txt. (Thoguh it already had 1)

I still get the same problem. I also tried changing ports and USB cable.

Please suggest

Thankyou
Regards
Logged

México
Offline Offline
Newbie
*
Karma: 0
Posts: 2
Buen dia!!!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Gooooooooooooooood, My Arduino Mini 04 it's working.
-Windows 7 64 bits
-Arduino 0022
-Sparkfun Items: DEV-08164 and DEV-08165

with the modify in the file boards.txt:

##############################################################

mini328.name=Arduino Mini with ATmega328

mini328.upload.protocol=stk500
mini328.upload.maximum_size=28672
mini328.upload.speed=115200

mini328.bootloader.low_fuses=0xff
mini328.bootloader.high_fuses=0xd8
mini328.bootloader.extended_fuses=0x05
mini328.bootloader.path=bt
mini328.bootloader.file=ATmegaBOOT_168_atmega328.hex
mini328.bootloader.unlock_bits=0x3F
mini328.bootloader.lock_bits=0x0F

mini328.build.mcu=atmega328p
mini328.build.f_cpu=16000000L
mini328.build.core=arduino
Logged

Ing. Surinam Zambrano S.
Ingeniero en Sistemas
Tel Móvil: +52-656-310-1572

Diseño de Sistemas Ingenieriles, S. de R.L. Mi. (DSI / Electroni

Offline Offline
Jr. Member
**
Karma: 0
Posts: 54
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Same situation, same problem. I get this error:



avrdude: Yikes!  Invalid device signature.
         Double check connections and try again, or use -F to override
         this check.
Logged

Pages: 1 [2]   Go Up
Jump to: