Go Down

Topic: Can't upload to Arduino NG (Read 486 times) previous topic - next topic

brodul

I use gentoo linux with arduino version 0021.

I have the Arduino NG conected to my PC via USB:

Code: [Select]
[ 3171.807540] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0004
[ 3171.807551] ehci_hcd 0000:00:1d.7: GetStatus port:2 status 001803 0  ACK POWER sig=j CSC CONNECT
[ 3171.807559] hub 2-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
[ 3171.911030] hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
[ 3171.962289] ehci_hcd 0000:00:1d.7: port 2 full speed --> companion
[ 3171.962296] ehci_hcd 0000:00:1d.7: GetStatus port:2 status 003801 0  ACK POWER OWNER sig=j CONNECT
[ 3171.962309] usb usb6: wakeup_rh (auto-start)
[ 3171.962317] hub 2-0:1.0: port 2 not reset yet, waiting 50ms
[ 3172.013054] ehci_hcd 0000:00:1d.7: GetStatus port:2 status 003002 0  ACK POWER OWNER sig=se0 CSC
[ 3172.013075] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0004
[ 3172.013082] uhci_hcd 0000:00:1d.0: port 2 portsc 0093,00
[ 3172.013089] hub 6-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
[ 3172.117048] hub 6-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101
[ 3172.219048] usb 6-2: new full speed USB device using uhci_hcd and address 4
[ 3172.339043] usb 6-2: ep0 maxpacket = 8
[ 3172.376351] usb 6-2: default language 0x0409
[ 3172.405352] usb 6-2: udev 4, busnum 6, minor = 643
[ 3172.405356] usb 6-2: New USB device found, idVendor=0403, idProduct=6001
[ 3172.405359] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3172.405361] usb 6-2: Product: FT232R USB UART
[ 3172.405364] usb 6-2: Manufacturer: FTDI
[ 3172.405366] usb 6-2: SerialNumber: A3000X14
[ 3172.405453] usb 6-2: usb_probe_device
[ 3172.405456] usb 6-2: configuration #1 chosen from 1 choice
[ 3172.408359] usb 6-2: adding 6-2:1.0 (config #1, interface 0)
[ 3172.413393] ftdi_sio 6-2:1.0: usb_probe_interface
[ 3172.413397] ftdi_sio 6-2:1.0: usb_probe_interface - got id
[ 3172.413402] ftdi_sio 6-2:1.0: FTDI USB Serial Device converter detected
[ 3172.413425] usb 6-2: Detected FT232RL
[ 3172.413427] usb 6-2: Number of endpoints 2
[ 3172.413429] usb 6-2: Endpoint 1 MaxPacketSize 64
[ 3172.413432] usb 6-2: Endpoint 2 MaxPacketSize 64
[ 3172.413434] usb 6-2: Setting MaxPacketSize 64
[ 3172.414410] usb 6-2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 3172.414434] drivers/usb/core/inode.c: creating file '004'
[ 3172.414457] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0004
[ 3172.414464] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0004


The error is:
Code: [Select]
Binary sketch size: 450 bytes (of a 14336 byte maximum)
Binary sketch size: 450 bytes (of a 14336 byte maximum)
avrdude: stk500_getsync(): not in sync: resp=0x60
avrdude: stk500_disable(): protocol error, expect=0x14, resp=0x60


The serial monitor returs:
Code: [Select]
T:582 I:10.64 U:344.59 P:3667.44 S:0.12 Q:31622.07 F:0.00
T:583 I:10.64 U:344.57 P:3666.43 S:0.12 Q:31621.95 F:0.00
T:584 I:10.64 U:344.59 P:3667.12 S:0.12 Q:31622.04 F:0.00
T:585 I:10.64 U:344.58 P:3666.36 S:0.12 Q:31621.86 F:0.00
T:586 I:10.64 U:344.62 P:3667.97 S:0.12 Q:31622.09 F:0.00
T:587 I:10.65 U:344.77 P:3670.65 S:0.12 Q:31621.95 F:0.00
T:588 I:10.64 U:344.56 P:3666.58 S:0.12 Q:31622.18 F:0.00
T:589 I:10.64 U:344.60 P:3667.90 S:0.12 Q:31622.12 F:0.00
T:590 I:10.65 U:344.82 P:3672.21 S:0.12 Q:31622.04 F:0.00
T:591 I:10.63 U:344.24 P:3660.18 S:0.12 Q:31623.26 F:0.00
T:592 I:10.63 U:344.13 P:3657.94 S:0.12 Q:31623.77 F:0.00
T:593 I:10.63 U:344.19 P:3658.60 S:0.12 Q:31623.71 F:0.00
T:594 I:10.64 U:344.44 P:3664.81 S:0.12 Q:31622.36 F:0.00
T:595 I:10.64 U:344.40 P:3664.05 S:0.12 Q:31622.41 F:0.00
T:596 I:10.63 U:344.47 P:3663.23 S:0.12 Q:31622.01 F:0.00
T:597 I:10.65 U:344.89 P:3673.20 S:0.12 Q:31621.94 F:0.00


I have the /dev/ttyUSB0 selected in upload progrem and the NG chip/version.
the L LED is blinking on off every ~second


johnwasser

Looks to me like the Arduino is not getting reset in preparation to receive a new sketch.  Hold down the Reset button on the Arduino and click on the upload button in the IDE.  When the message "Binary sketch size:" appears in the IDE, release the reset button.
Send Bitcoin tips to: 1L3CTDoTgrXNA5WyF77uWqt4gUdye9mezN
Send Litecoin tips to : LVtpaq6JgJAZwvnVq3ftVeHafWkcpmuR1e

brodul

Tnx this solves the problem.

Now I get:
Code: [Select]
avrdude: stk500_recv(): programmer is not responding


But when I upload with procedure above. I don.t get an error.
Then I have to unplug and plug the Arduino NG and the program is running.

TNX for support

Go Up
 


Please enter a valid email to subscribe

Confirm your email address

We need to confirm your email address.
To complete the subscription, please click the link in the email we just sent you.

Thank you for subscribing!

Arduino
via Egeo 16
Torino, 10131
Italy