Go Down

Topic: facing issues while uploading programs on Arduino to breadboard (Read 69 times) previous topic - next topic

gflawless

I am trying to upload a program on Arduino to Breadboard. Bootloader is already burnt. Earlier few times I have programmed it with the same process without any issue. But now I have tried it several times but with no luck. PFB the details:

1. Operating System: Windows
2. Board : Arduino Uno
3. Earlier I have uploaded programs without any issue. I haven't updated any software in my laptop.
4. Error messages I got:

Arduino: 1.8.5 (Windows 7), Board: "Arduino/Genuino Uno"

Sketch uses 22610 bytes (70%) of program storage space. Maximum is 32256 bytes.
Global variables use 1194 bytes (58%) of dynamic memory, leaving 854 bytes for local variables. Maximum is 2048 bytes.
C:\Users\g@ur@vfl@wless\Desktop\Arduino\hardware\tools\avr/bin/avrdude -CC:\Users\g@ur@vfl@wless\Desktop\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM4 -b115200 -D -Uflash:w:C:\Users\G@UR@V~1\AppData\Local\Temp\arduino_build_651705/sketch_nov04a_consolidated.ino.hex:i

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Users\g@ur@vfl@wless\Desktop\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM4
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x0d
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x0d

avrdude done.  Thank you.

Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
Code: [Select]

Go Up