Go Down

Topic: Controllino Mini PLC not uploading (Read 260 times) previous topic - next topic

zoooza

Nov 27, 2018, 10:25 pm Last Edit: Nov 27, 2018, 10:26 pm by zoooza
Hi All,

I can not upload any sketches to my Controllino Mini PLC!

It was working fine and stopped all of a sudden.

Tried different cable, computer and still the same results.

When I ask to get board info, the information displayed correctly, without any problems.

Any recommendation would be very appreciated.



pert

Please do this:
  • File > Preferences > Show verbose output during: > compilation (uncheck) > upload (check) > OK
  • Attempt an upload
  • After the upload fails you'll see a button on the right side of the orange bar "Copy error messages". Click that button.
  • Paste the error messages in a reply here USING CODE TAGS (</> button on the forum toolbar).

zoooza

Thank you in advance ...

Code: [Select]
Arduino: 1.8.7 (Windows Store 1.8.15.0) (Windows 10), Board: "CONTROLLINO MINI"

Sketch uses 3804 bytes (11%) of program storage space. Maximum is 32256 bytes.
Global variables use 236 bytes (11%) of dynamic memory, leaving 1812 bytes for local variables. Maximum is 2048 bytes.
C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.15.0_x86__mdqgnx93n4wtt\hardware\tools\avr/bin/avrdude -CC:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.15.0_x86__mdqgnx93n4wtt\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM5 -b115200 -D -Uflash:w:C:\Users\zina\AppData\Local\Temp\arduino_build_966690/WaterValve_mini2.ino.hex:i

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.15.0_x86__mdqgnx93n4wtt\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM5
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
         AVR Part                      : ATmega328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : Arduino
         Description     : Arduino

avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
         Hardware Version: 4744608
         Firmware Version: 0.4611299
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
         Vtarget         : 420030.5 V
         Varef           : 195954438.4 V
         Oscillator      : 0.531 Hz
         SCK period      : 12552803.9 us

avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.

avrdude: stk500_recv(): programmer is not responding

avrdude done.  Thank you.

the selected serial port
 does not exist or your board is not connected

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

zoooza


InRo

#4
Feb 11, 2019, 05:32 pm Last Edit: Feb 11, 2019, 06:02 pm by InRo
Hi Guys,

So any Ideas ?


Well - it is exactly the same problem I have. Even verbose errors are the same! Possibly some issue with this product - I still have warranty so will complain to Controllino.

https://forum.arduino.cc/index.php?topic=596536.0

EDIT:
Solution:  https://arduino.stackexchange.com/questions/22591/did-i-brick-my-controllino



pert

Thanks for taking the time to share your solution InRo!

Go Up