Go Down

Topic: Arduino and NFC (Read 13389 times) previous topic - next topic


Hi! I'm new to Arduino, and I want to ask you some questions about nfc :)
Is there any shield for arduino that acts as an nfc reader?
if not can I use an rfid reader to read nfc tags?

The last: has anyone done something that works with arduino and nfc?

Thanks :)


nfc ? No Freakin' Chicken?
Designing & building electrical circuits for over 25 years.  Screw Shield for Mega/Due/Uno,  Bobuino with ATMega1284P, & other '328P & '1284P creations & offerings at  my website.


NFC = Near Field Communication    ==>   - http://en.wikipedia.org/wiki/Near_field_communication -

with respect to your question => I have no experience
Rob Tillaart

Nederlandse sectie - http://arduino.cc/forum/index.php/board,77.0.html -
(Please do not PM for private consultancy)


"Uses and applicationsNFC technology is intended mainly for use in mobile phones.[3] There are currently three specific uses for NFC according to the NFC Forum:

Reader/writer mode: the NFC device is active and reads a passive RFID tag. Example: smart posters."

RFID reader sounds like a possibility. => also no experience
Designing & building electrical circuits for over 25 years.  Screw Shield for Mega/Due/Uno,  Bobuino with ATMega1284P, & other '328P & '1284P creations & offerings at  my website.


Count me among the "no experience" crowd. But I did read over in the Adafruit forums that they will be selling this:


Not a shield per se, but might be relevant.


Haven't used Adafruit's Breakout Board (would love to, but it's been out of stock for a while now) but I have used an NXP PN532 C106 development board via SPI mode talking to an Arduino. Worked just fine and the Adafruit site also has a library for it that works well; though they only read tags; not really complete as Android to be writing to tags, parsing NDEF records, etc. But that kind of thing isn't too hard to add on your own if you need it.

Just make sure you use a level converter to do 5v/3.3v; or I prefer a Seeeduino board because I can switch the logic level to 3.3v or 5v without needing an extra converter chip.


Try going through hackaday.com... there was a tutorial about the NFC inside the new Nexus S that may be of use to you.

I'll try finding it later on.
Eu não sou o teu criado. Se respondo no fórum é para ajudar todos mediante a minha disponibilidade e disposição. Responder por mensagem pessoal iria contra o propósito do fórum e por isso evito-o.
Se realmente pretendes que eu te ajude por mensagem pessoal, então podemos chegar a um acordo e contrato onde me pagas pela ajuda que eu fornecer e poderás então definir os termos de confidencialidade do meu serviço. De forma contrária toda e qualquer ajuda que eu der tem de ser visível a todos os participantes do fórum (será boa ideia, veres o significado da palavra fórum).
Nota também que eu não me responsabilizo por parvoíces escritas neste espaço pelo que se vais seguir algo dito por mim, entende que o farás por tua conta e risco.

Dito isto, mensagens pessoais só se forem pessoais, ou seja, se já interagimos de alguma forma no passado ou se me pretendes convidar para uma churrascada com cerveja (paga por ti, obviamente).


I experimented with a couple of cheap RFID readers with USB interface - from USB perspective they act like HID keyboards. Here's an article how to read USB keyboard -> http://www.circuitsathome.com/mcu/how-to-drive-usb-keyboard-from-arduino and here's another which shows how to interface with HID devices in general -> http://www.circuitsathome.com/communicating-arduino-with-hid-devices-part-1 RFID readers are aplenty at eBay.


If you are happy working with MIFARE cards only (by far the most widespread) you can pick up an unexpensive modules from http://www.stronglink.cn/english/module.htm

With these modules you don't need a shield, just a few wires as described here: http://ls6.posterous.com/arduino-and-nfc-part-1

Go Up