Pages: [1]   Go Down
Author Topic: =( Please Help me =(  (Read 2081 times)
0 Members and 1 Guest are viewing this topic.
Dubai , UAE
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Hi there,  smiley-red


I am beginner in Arduino Uno. In addition I have basic knowledge about electronics and programing. I am planning to do airship ((blimp)) for UAE National Day. Everything’s perfect from mechanical side except the programing. I don’t how to program the arduino uno codes. Please help me with the prepared codes and how I can I fix the input and output (where I put the signal wires) in my arduino uno.

The tools which I have are:

3 servos
2 motors with speed control
2 LED with resister
1 FM receiver - 8channel (Futaba -R168DF)
1 remote control (Futaba - T6EXP) - (PCM 1024)
1 battery 7.25 V 

Please Help me  smiley-cry with it

thanks smiley-kitty
Logged

Seattle, WA USA
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 46026
Seattle, WA USA
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
1 FM receiver - 8channel (Futaba -R168DF)
1 remote control (Futaba - T6EXP) - (PCM 1024)
So, connect the 3 servos and 2 motors to the receiver.

Connect the battery to the servo power wires and grounds.

Duct tape the Arduino and LEDs on the outside. It doesn't seem to have a purpose.
Logged

Dubai , UAE
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

thinks PaulS  smiley-kiss

I have done this before. Now I want to do it with Arduino   smiley

thinks  smiley-lol
Logged

Global Moderator
UK
Offline Offline
Brattain Member
*****
Karma: 238
Posts: 24317
I don't think you connected the grounds, Dave.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
Now I want to do it with Arduino
If only we knew what "it" was, maybe we could help you.
Logged

"Pete, it's a fool looks for logic in the chambers of the human heart." Ulysses Everett McGill.
Do not send technical questions via personal messaging - they will be ignored.

Dubai , UAE
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

 smiley-lol I controlled the servo and motors direct from the receiver  smiley-cool

 smiley-fat Now I want to control them throw Arduino   smiley-fat

 smiley-evil using remote control  smiley-twist

thanks  smiley-kiss
Logged

Global Moderator
UK
Offline Offline
Brattain Member
*****
Karma: 238
Posts: 24317
I don't think you connected the grounds, Dave.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Why do you want to make an aerial vehicle less reliable?
Logged

"Pete, it's a fool looks for logic in the chambers of the human heart." Ulysses Everett McGill.
Do not send technical questions via personal messaging - they will be ignored.

Seattle, WA USA
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 46026
Seattle, WA USA
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Quote
Now I want to control them throw Arduino
You want the servos to throw the Arduino? I don't get it.
Logged

Dubai , UAE
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

this what i men  smiley-lol






i don't how i program the arduino and wear to put the input and the output in my arduino  smiley-cry 


* DSC00004.jpg (51.13 KB, 640x480 - viewed 22 times.)

* DSC00005.jpg (51.19 KB, 640x480 - viewed 20 times.)
Logged

Leighton Buzzard, UK
Offline Offline
Edison Member
*
Karma: 20
Posts: 1318
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

what do you want the arduino to do ?
Logged

there are only 10 types of people
them that understands binary
and them that doesn't

Dubai , UAE
Offline Offline
Newbie
*
Karma: 0
Posts: 5
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Basic things

To take command from FM Receiver convert to the contacted servos and motors


Motor for speed

2 Servo in different degree both start with 90 degree if I posh the remote gear up servo goes to 180 degree if I pull down servo go to 0 degree
Logged

Global Moderator
UK
Offline Offline
Brattain Member
*****
Karma: 238
Posts: 24317
I don't think you connected the grounds, Dave.
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

But you can do that more effectively and with less risk with just a length of wire.
Logged

"Pete, it's a fool looks for logic in the chambers of the human heart." Ulysses Everett McGill.
Do not send technical questions via personal messaging - they will be ignored.

Seattle, WA USA
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 46026
Seattle, WA USA
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Connect the things that make sense (the motors and servos) directly to the receiver. Connect the unused channels to digital pins, and use pulseIn to collect data from those channels/pins. Use that data for whatever.

You need to define what type of data comes over the unused channels, and what the Arduino should do with it. Then, coding help makes sense.

Having the Arduino read all the channels, and convert the signals to times and back to servo signals doesn't.
Logged

Pages: [1]   Go Up
Jump to: