Pages: [1]   Go Down
Author Topic: arduino clone  (Read 1865 times)
0 Members and 1 Guest are viewing this topic.
Offline Offline
Newbie
*
Karma: 0
Posts: 35
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

i had a look at some other arduino clone circuits and i designed my own basic arduino clone the circuit is attached below as i am new to all this i am asking to see if it will work i think it will but i am not sure


* img078.jpg (2023.71 KB, 3063x2125 - viewed 61 times.)
Logged

0
Offline Offline
Edison Member
*
Karma: 8
Posts: 1411
Arduino rocks
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

It looks ok.
You will need to add a 6-pin header to connect to an FTDI breakout, for uploading sketches.
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 27372
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

He does have an FTDI header. Not organized to accept an FTDI Basic as is, but easily re-organized. Needs a 0.1uF cap between the reset on the connector pin and the reset pin.  Having the 0.1uF caps across the VCC, AVCC, and AREF pins to gnd also helps to show that decoupling is understood.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

South Texas
Offline Offline
Edison Member
*
Karma: 8
Posts: 1025
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

Just the de-coupling caps, other than that it looks good.
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 35
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

is this now ok


* img079.jpg (2182.67 KB, 3044x2139 - viewed 31 times.)
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 27372
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Change the header order like this:
Gnd
Gnd
Vcc (+5)
Rx  [ edit - swapped Rx & Tx - these reflect the uC pins]
Tx
DTR (just rename it, goes to the reset capacitor)

Then put 3.3V on it somewhere if you want.
This way you can plug on an FTDI Basic for downloading sketches.
http://www.gravitech.us/arliandpropr.html
« Last Edit: February 28, 2012, 07:42:09 pm by CrossRoads » Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Offline Offline
Newbie
*
Karma: 0
Posts: 35
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

ok i will do that and can i use a ATmega328 on it 
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 27372
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

Yes and yes.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Offline Offline
Newbie
*
Karma: 0
Posts: 35
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

thanks
Logged

Offline Offline
Newbie
*
Karma: 0
Posts: 35
View Profile
 Bigger Bigger  Smaller Smaller  Reset Reset

when programming it with a USB to TTL converter does the TXD pin on the converter go to pin 3 on the ATmega328 (TXD pin on the chip)
Logged

Global Moderator
Boston area, metrowest
Offline Offline
Brattain Member
*****
Karma: 548
Posts: 27372
Author of "Arduino for Teens". Available for Design & Build services. Now with Unlimited Eagle board sizes!
View Profile
WWW
 Bigger Bigger  Smaller Smaller  Reset Reset

These pins in this order:

Gnd
Gnd
Vcc (+5)
Rx  [ edit - swapped Rx & Tx - these reflect the uC pins]
Tx
DTR

reflect the uC names.
The FTDI will then connect its Rx to the uC Tx, and its Tx will connect to uC Rx.
Logged

Designing & building electrical circuits for over 25 years. Check out the ATMega1284P based Bobuino and other '328P & '1284P creations & offerings at  www.crossroadsfencing.com/BobuinoRev17.
Arduino for Teens available at Amazon.com.

Pages: [1]   Go Up
Jump to: