Go Down

Topic: My home-brew Arduino OBD-II connection kit (Read 50 times) previous topic - next topic

cmendes0101

I think this is awesome.

I've always used an OBDII reader on my car but always hassle with having to drag my laptop around or using up my phone, which also means I have to plan ahead and didn't have a seamless way with out sitting in the car getting everything started before driving. Should record everything even on quick trips around town without me doing anything or watching a screen.

I hope to give this a shot!

DaveyRavey

Hi, I'm looking to do the opposite, I have an aftermarket ECU which I can get data out of from via a serial cable but I'd like to make this available to the ODB port for the ELM to read so a standard ODB code reader/ODB software will work, is this likely to be possible with the experience you've gained from doing your project?

Thanks

RudiAhlers

This looks like a great project and could be very useful.

As matter of interest, where do you find the different codes / commands for the car, if you for instance want to "check all the systems", or adjust the CO2, or something like that?

Peakdesign

#13
Jul 28, 2013, 10:11 am Last Edit: Jul 28, 2013, 11:13 am by Peakdesign Reason: 1
First of all, download and read the ELM327 docs at the Elm Electronics site.

http://elmelectronics.com/obdic.html#ELM327

They made the Industry Standard decoder firmware for a PIC18 microcontroller that they called ELM327. It can talk to a car's ECU computer over most of the protocols in use, and convert them into a common ASCII form. OBD is the standard connector, with different car makes and models using different protocols over different pins on the connector. Software vendors then created allegedly specialized monitoring packages using the ELM327 for this or that car, at hefty prices. Companies in Asia then copied the ELM327 firmware and started selling clones using the PIC18 or other microcontrollers, presented through various interfaces: USB, Bluetooth, Serial, WiFi. These are available on e-bay at low prices. Some are better than others. I just got a working $15 unit with a USB plug that can be used with any computer that can virtualize a device USB connection as a COM port. There are many teaser PC programs available that allow you to read a handful of parameters (so you buy their full package), but a terminal program works too.

What Stanley is offering is an ELM327-compatible OBD-II interface, with a cable bearing TTL compatible serial data, so it can be directly connected to e.g. Arduino I/O pins. It's then a simple serial connection that any Arduino buff can use to query, store and display the desired car parameters, with Stanley providing some useful example code.

The place to start is understanding the base AT commands to control the ELM327, and then the deeper OBD "PID"s that can be used to request this or that specific parameter from the engine. OBD is mostly a "read-only" monitoring system, but not entirely. One of the clearer PID lists is on Wikipedia:

http://en.wikipedia.org/wiki/Table_of_OBD-II_Codes

You can use a terminal program to get your bearings. For Instance typing the ATI command (followed by Carriage Return) will probably evoke a reply like "ELM327 v1.5", though ELM never made a version 1.5. Once the interface is mated with the OBD connector on the car, you can type ATRV and read the battery voltage. Yes, there is a simple command to clear the annoying Engine Warning Light and wipe ALL the associated logs and diagnostic data, in one fell swoop, so I won't tell you what that is.

@DaveyRavey's request is more difficult. The ELM327s convert some quite knarly protocols into clear ASCII. To mimic an ECU talking from the car side of the OBD connector entails fully understanding and then emulating one of these protocols, complete with its specific modulations scheme, handshakes and error handling. Many of these protocols use the old annoying (and ineffective) "security through NDA and obfuscation" technique to waste your time.

foster182

Hi, i'm looking at getting into a project like this.
I own a japanese import car which is not obd2 compliant.
It uses some jobd protocol.

I'm just curious will this connection help me to read information coming from the ecu.
Also how with a obtain information coming from the ecu, would i just use the tx and rx pins?

Thanks.

Go Up