@rpt007
I changed nothing in my windows configuration...
OS- Windows 8.1
IDE - 1.6.12
USB - 3.0
No nothing is connected to the board, I tried again with the simple hello world program...
My arduino is detectable in device manager devices under PORTS (COM & LPT)..
Since that board got dead I moved from that arduino UNO to MKR1000 for my project, but after this thread's response today I tried again to upload on UNO board, I tried just simple Hello print code
void setup() {
Serial.begin(9600);
// put your setup code here, to run once:
}
void loop() {
Serial.println("Hello arduino");
delay(5000);
// put your main code here, to run repeatedly:
}
But again I got the following error
avrdude: Version 6.3, compiled on Sep 12 2016 at 17:24:16
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM16
Using Programmer : arduino
Overriding Baud Rate : 115200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: reading input file "C:\Users\PRODUC~1.ODS\AppData\Local\Temp\arduino_build_505651/arduino_trial.ino.hex"
avrdude: writing flash (1592 bytes):
Writing | ################################################## | 100% 0.21s
avrdude: 1592 bytes of flash written
avrdude: verifying flash memory against C:\Users\PRODUC~1.ODS\AppData\Local\Temp\arduino_build_505651/arduino_trial.ino.hex:
avrdude: load data flash data from input file C:\Users\PRODUC~1.ODS\AppData\Local\Temp\arduino_build_505651/arduino_trial.ino.hex:
avrdude: input file C:\Users\PRODUC~1.ODS\AppData\Local\Temp\arduino_build_505651/arduino_trial.ino.hex contains 1592 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 0.21s
avrdude: verifying ...
avrdude: verification error, first mismatch at byte 0x0000
0x62 != 0x0c
the selected serial port 0x62 != 0x0c
does not exist or your board is not connected
avrdude: verification error; content mismatch
avrdude done. Thank you.
Thanks..