Arduino Uno send temperature data "GET" method - problem

Using Arduino Sensors
1

Hello,

i have problem with sending temp data (ds18b20)via enc28j60. If i use sensor BMP085, all works.

There is main code:

  • Arduino receive IP address from DHCP and then frozen is it
#include <OneWire.h>
#include <EtherCard.h>

OneWire  ds(2);  // on pin 10
// ethernet interface mac address, must be unique on the LAN
static byte mymac[] = { 0x74,0x69,0x69,0x2D,0x30,0x31 };

byte Ethernet::buffer[700];
static uint32_t timer;

char website[] PROGMEM = "192.168.1.37";

// called when the client request is complete
static void my_callback (byte status, word off, word len) {
  Serial.println(">>>");
  Ethernet::buffer[off+300] = 0;
  Serial.print((const char*) Ethernet::buffer + off);
  Serial.println("...");
}

void setup(void) {
  Serial.begin(9600);
  if (ether.begin(sizeof Ethernet::buffer, mymac) == 0) 
    Serial.println( "Failed to access Ethernet controller");
  if (!ether.dhcpSetup())
    Serial.println("DHCP failed");

  ether.printIp("IP:  ", ether.myip);
  ether.printIp("GW:  ", ether.gwip);  
  ether.printIp("DNS: ", ether.dnsip);  

  if (!ether.dnsLookup(website))
    Serial.println("DNS failed");
    
  ether.printIp("SRV: ", ether.hisip);
}

void loop(void) {
  byte i;
  byte present = 0;
  byte type_s;
  byte data[12];
  byte addr[8];
  float celsius, fahrenheit;
  
  if ( !ds.search(addr)) {
    ds.reset_search();
    delay(250);
    return;
  }
  
  for( i = 0; i < 8; i++) {
  }

  if (OneWire::crc8(addr, 7) != addr[7]) {
      return;
  }
 
  switch (addr[0]) {
    case 0x10:
      type_s = 1;
      break;
    case 0x28:
      type_s = 0;
      break;
    case 0x22:
      type_s = 0;
      break;
    default:
      return;
  } 

  ds.reset();
  ds.select(addr);
  ds.write(0x44,1);         // start conversion, with parasite power on at the end
  
  delay(1000);     // maybe 750ms is enough, maybe not
  // we might do a ds.depower() here, but the reset will take care of it.
  
  present = ds.reset();
  ds.select(addr);    
  ds.write(0xBE);         // Read Scratchpad

  for ( i = 0; i < 9; i++) {           // we need 9 bytes
    data[i] = ds.read();
  }

  // convert the data to actual temperature

  unsigned int raw = (data[1] << 8) | data[0];
  if (type_s) {
    raw = raw << 3; // 9 bit resolution default
    if (data[7] == 0x10) {
      raw = (raw & 0xFFF0) + 12 - data[6];
    }
  } else {
    byte cfg = (data[4] & 0x60);
    if (cfg == 0x00) raw = raw << 3;  // 9 bit resolution, 93.75 ms
    else if (cfg == 0x20) raw = raw << 2; // 10 bit res, 187.5 ms
    else if (cfg == 0x40) raw = raw << 1; // 11 bit res, 375 ms
  }
  celsius = (float)raw / 16.0;
  Serial.print("Temperature = ");
  Serial.print(celsius);
  Serial.print(" Celsius ");
  Serial.println();
   
    ether.packetLoop(ether.packetReceive());

    float stupen = celsius; // or whatever
    char tempik[7];
    dtostrf(stupen, 5, 2,tempik);
    
  if (millis() > timer) {
    timer = millis() + 10000;
    ether.browseUrl(PSTR("/temper.php?temp="),tempik, website, NULL);
  }
}

please help :roll_eyes:

2

Can you make a minimal test sketch for the DS18B20, and send the temperature to the serial monitor ?
You have place some code for the DS18B20 into the loop() function, but it should not be done like that. Where did you find the example code ?