Help with error messages when uploading

nickevasion · January 13, 2018, 8:35pm

Hi I've been having trouble uploading sketches to my Leonardo. It was working fine about a week ago, but now whenever I upload a sketch, I get this error message

Global variables use 149 bytes (5%) of dynamic memory, leaving 2411 bytes for local variables. Maximum is 2560 bytes.
Forcing reset using 1200bps open/close on port COM11
PORTS {COM11, } / {} => {}
PORTS {} / {COM11, } => {COM11, }
Found upload port: COM11
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega32u4 -cavr109 -PCOM11 -b57600 -D -Uflash:w:C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.hex:i 

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM11
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega32U4
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  9000  9000 0x00 0x00
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : butterfly
         Description     : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

The troubleshooting guide didn't really help at all.

As I've been using arduino for maybeeee 2 weeks now, this is very confusing and frustrating. What is a
.avrdude? Why is it mad at the butterflies?

Now when i upload code to my UNO, i get a similar error message, but the code is uploaded. The IDE will noT let me copy this code, because it ends up uploading onto the arduino. I have included the error (not error?) messages for the UNO as screenshots in the attachments.

(please do not spam "THIS IS THE WRONG POSTING PROCEDURE READ THIS POST LOSER DURRRRRRRRRRRRRFJSDKHFJKSDGNKJ" if i should include this in another way.)

I would really appreciate some help on this. should I reinstall the IDE? Buy a new Leonardo? Get a new cable?
Please & Thank you
-Nick

system · January 13, 2018, 8:45pm

(deleted)

nickevasion · January 13, 2018, 8:52pm

Damn haha i'll get it right next time sorry guys

Ok so i hit reset, and got this error message

Arduino: 1.8.5 (Windows 10), Board: "Arduino Leonardo"

C:\Program Files (x86)\Arduino\arduino-builder -dump-prefs -logger=machine -hardware C:\Program Files (x86)\Arduino\hardware -tools C:\Program Files (x86)\Arduino\tools-builder -tools C:\Program Files (x86)\Arduino\hardware\tools\avr -built-in-libraries C:\Program Files (x86)\Arduino\libraries -libraries C:\Users\Nick\Documents\Arduino\libraries -fqbn=arduino:avr:leonardo -vid-pid=0X2341_0X8036 -ide-version=10805 -build-path C:\Users\Nick\AppData\Local\Temp\arduino_build_735511 -warnings=none -build-cache C:\Users\Nick\AppData\Local\Temp\arduino_cache_831242 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.arduinoOTA.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.avr-gcc.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.avrdude.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -verbose C:\Program Files (x86)\Arduino\examples\01.Basics\Blink\Blink.ino
C:\Program Files (x86)\Arduino\arduino-builder -compile -logger=machine -hardware C:\Program Files (x86)\Arduino\hardware -tools C:\Program Files (x86)\Arduino\tools-builder -tools C:\Program Files (x86)\Arduino\hardware\tools\avr -built-in-libraries C:\Program Files (x86)\Arduino\libraries -libraries C:\Users\Nick\Documents\Arduino\libraries -fqbn=arduino:avr:leonardo -vid-pid=0X2341_0X8036 -ide-version=10805 -build-path C:\Users\Nick\AppData\Local\Temp\arduino_build_735511 -warnings=none -build-cache C:\Users\Nick\AppData\Local\Temp\arduino_cache_831242 -prefs=build.warn_data_percentage=75 -prefs=runtime.tools.arduinoOTA.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.avr-gcc.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -prefs=runtime.tools.avrdude.path=C:\Program Files (x86)\Arduino\hardware\tools\avr -verbose C:\Program Files (x86)\Arduino\examples\01.Basics\Blink\Blink.ino
Using board 'leonardo' from platform in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr
Using core 'arduino' from platform in folder: C:\Program Files (x86)\Arduino\hardware\arduino\avr
Detecting libraries used...
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics  -flto -w -x c++ -E -CC -mmcu=atmega32u4 -DF_CPU=16000000L -DARDUINO=10805 -DARDUINO_AVR_LEONARDO -DARDUINO_ARCH_AVR  -DUSB_VID=0x2341 -DUSB_PID=0x8036 '-DUSB_MANUFACTURER="Unknown"' '-DUSB_PRODUCT="Arduino Leonardo"' "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\leonardo" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\sketch\Blink.ino.cpp" -o "nul"
Generating function prototypes...
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics  -flto -w -x c++ -E -CC -mmcu=atmega32u4 -DF_CPU=16000000L -DARDUINO=10805 -DARDUINO_AVR_LEONARDO -DARDUINO_ARCH_AVR  -DUSB_VID=0x2341 -DUSB_PID=0x8036 '-DUSB_MANUFACTURER="Unknown"' '-DUSB_PRODUCT="Arduino Leonardo"' "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\leonardo" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\sketch\Blink.ino.cpp" -o "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\preproc\ctags_target_for_gcc_minus_e.cpp"
"C:\Program Files (x86)\Arduino\tools-builder\ctags\5.8-arduino11/ctags" -u --language-force=c++ -f - --c++-kinds=svpf --fields=KSTtzns --line-directives "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\preproc\ctags_target_for_gcc_minus_e.cpp"
Compiling sketch...
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-g++" -c -g -Os -w -std=gnu++11 -fpermissive -fno-exceptions -ffunction-sections -fdata-sections -fno-threadsafe-statics -MMD -flto -mmcu=atmega32u4 -DF_CPU=16000000L -DARDUINO=10805 -DARDUINO_AVR_LEONARDO -DARDUINO_ARCH_AVR  -DUSB_VID=0x2341 -DUSB_PID=0x8036 '-DUSB_MANUFACTURER="Unknown"' '-DUSB_PRODUCT="Arduino Leonardo"' "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\cores\arduino" "-IC:\Program Files (x86)\Arduino\hardware\arduino\avr\variants\leonardo" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\sketch\Blink.ino.cpp" -o "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\sketch\Blink.ino.cpp.o"
Compiling libraries...
Compiling core...
Using precompiled core
Linking everything together...
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-gcc" -w -Os -g -flto -fuse-linker-plugin -Wl,--gc-sections -mmcu=atmega32u4  -o "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.elf" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511\sketch\Blink.ino.cpp.o" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/..\arduino_cache_831242\core\core_arduino_avr_leonardo_0c812875ac70eb4a9b385d8fb077f54c.a" "-LC:\Users\Nick\AppData\Local\Temp\arduino_build_735511" -lm
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -j .eeprom --set-section-flags=.eeprom=alloc,load --no-change-warnings --change-section-lma .eeprom=0  "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.elf" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.eep"
"C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avr-objcopy" -O ihex -R .eeprom  "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.elf" "C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.hex"
Sketch uses 4128 bytes (14%) of program storage space. Maximum is 28672 bytes.
Global variables use 149 bytes (5%) of dynamic memory, leaving 2411 bytes for local variables. Maximum is 2560 bytes.
Forcing reset using 1200bps open/close on port COM11
PORTS {COM11, } / {} => {}
PORTS {} / {COM11, } => {COM11, }
Found upload port: COM11
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega32u4 -cavr109 -PCOM11 -b57600 -D -Uflash:w:C:\Users\Nick\AppData\Local\Temp\arduino_build_735511/Blink.ino.hex:i 

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM11
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
avrdude: ser_open(): can't open device "\\.\COM11": The system cannot find the file specified.



avrdude done.  Thank you.

Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

system · January 13, 2018, 8:58pm

(deleted)

nickevasion · January 14, 2018, 9:31pm

PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {COM12, } => {}
PORTS {COM12, } / {} => {}
PORTS {} / {COM11, } => {COM11, }
Found upload port: COM11
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega32u4 -cavr109 -PCOM11 -b57600 -D -Uflash:w:C:\Users\Nick\AppData\Local\Temp\arduino_build_235042/Blink.ino.hex:i 

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM11
         Using Programmer              : avr109
         Overriding Baud Rate          : 57600
         AVR Part                      : ATmega32U4
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65    20     4    0 no       1024    4      0  9000  9000 0x00 0x00
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0x00 0x00
           lfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  9000  9000 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : butterfly
         Description     : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .avrdude: ser_recv(): read error: The I/O operation has been aborted because of either a thread exit or an application request.


avrdude: butterfly_recv(): programmer is not responding

avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_drain(): read error: The device does not recognize the command.


avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
Found programmer: Id = "&"; type = @
    Software Version = ˆ.u; Hardware Version = “.ð
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: buffered memory access not supported. Maybe it isn't
a butterfly/AVR109 but a AVR910 device?
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.

avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
the selected serial port avrdude: butterfly_recv(): programmer is not responding
 does not exist or your board is not connected
avrdude: error: programmer did not respond to command: leave prog mode
avrdude: ser_send(): write error: sorry no info avail
avrdude: ser_recv(): read error: The device does not recognize the command.


avrdude: butterfly_recv(): programmer is not responding
avrdude: error: programmer did not respond to command: exit bootloader

avrdude done.  Thank you.

Topic		Replies	Views
An error occurred while uploading the sketch. IDE 1.x	134	455121	October 16, 2021
Upload not completing IDE 1.x	5	917	May 5, 2021
Arduino Sketch not Uploading IDE 1.x	3	1411	May 5, 2021
Error uploading code Mega 2650 IDE 1.x	4	938	May 5, 2021
upload error IDE 1.x	6	1160	May 5, 2021

Help with error messages when uploading

Related Topics