Jean-François:
Oups... un week end un peu mouvementé et du coup j'ai oublié de refaire les tests avec l'IDE 1.xx et Processing 2.xxLe tout sans lcd
Est ce que tu as essayé avec un lcd ?
Salut JF
coté arduino depuis la 1.00 les fonctions lecture/ecriture I²C ont changées
/*
Permet de mettre une horloge ds1307 en synchronisation avec l'heure NTP
Par le biais d'une application Arduino-Processing
*/
/*
Comporte des parties de code écrites par :
- Maurice Ribble
4-17-2008
http://www.glacialwanderer.com/hobbyrobotics
Pour le ds1307
- X. HINAULT
01/2010
http://www.mon-club-elec.fr
Pour le LCD
*/
#include "Wire.h"
#define DS1307_I2C_ADDRESS 0x68
// Convert normal decimal numbers to binary coded decimal
byte decToBcd(byte val)
{
return ( (val/10*16) + (val%10) );
}
// Convert binary coded decimal to normal decimal numbers
byte bcdToDec(byte val)
{
return ( (val/16*10) + (val%16) );
}
// Stops the DS1307, but it has the side effect of setting seconds to 0
// Probably only want to use this for testing
/*void stopDs1307()
{
Wire.beginTransmission(DS1307_I2C_ADDRESS);
Wire.write(0);
Wire.write(0x80);
Wire.endTransmission();
}*/
// 1) Sets the date and time on the ds1307
// 2) Starts the clock
// 3) Sets hour mode to 24 hour clock
// Assumes you're passing in valid numbers
void setDateDs1307(byte second, // 0-59
byte minute, // 0-59
byte hour, // 1-23
byte dayOfWeek, // 1-7
byte dayOfMonth, // 1-28/29/30/31
byte month, // 1-12
byte year) // 0-99
{
Wire.beginTransmission(DS1307_I2C_ADDRESS);
Wire.write(0);
Wire.write(decToBcd(second)); // 0 to bit 7 starts the clock
Wire.write(decToBcd(minute));
Wire.write(decToBcd(hour)); // If you want 12 hour am/pm you need to set
// bit 6 (also need to change readDateDs1307)
Wire.write(decToBcd(dayOfWeek));
Wire.write(decToBcd(dayOfMonth));
Wire.write(decToBcd(month));
Wire.write(decToBcd(year));
Wire.endTransmission();
}
// Gets the date and time from the ds1307
void getDateDs1307(
byte *second,
byte *minute,
byte *hour,
byte *dayOfWeek,
byte *dayOfMonth,
byte *month,
byte *year)
{
// Reset the register pointer
Wire.beginTransmission(DS1307_I2C_ADDRESS);
Wire.write(0);
Wire.endTransmission();
Wire.requestFrom(DS1307_I2C_ADDRESS, 7);
// A few of these need masks because certain bits are control bits
*second = bcdToDec(Wire.read() & 0x7f);
*minute = bcdToDec(Wire.read());
*hour = bcdToDec(Wire.read() & 0x3f); // Need to change this if 12 hour am/pm
*dayOfWeek = bcdToDec(Wire.read());
*dayOfMonth = bcdToDec(Wire.read());
*month = bcdToDec(Wire.read());
*year = bcdToDec(Wire.read());
}
#include <LiquidCrystal.h>
const int RS=2; //declaration constante de broche
const int E=3; //declaration constante de broche
const int D4=4; //declaration constante de broche
const int D5=5; //declaration constante de broche
const int D6=6; //declaration constante de broche
const int D7=7; //declaration constante de broche
LiquidCrystal lcd(RS, E, D4, D5, D6, D7);
int octetReception=0; // variable de stockage des valeurs reçues sur le port Série (ASCII)
char caractereRecu=0; // variable pour stockage caractère recu
int compt=0; // variable comptage caractères reçus
String chaineReception=""; // déclare un objet String vide pour reception chaine
int oldSecond;
void setup() {
byte second, minute, hour, dayOfWeek, dayOfMonth, month, year;
Wire.begin(); // initialise 1wire
Serial.begin(115200); // Initialise la communication série
// lit les valeurs de l'horloge pour les replacer si elle est déjà à l'heure
getDateDs1307(&second, &minute, &hour, &dayOfWeek, &dayOfMonth, &month, &year);
if ((year)== NULL){ // si l'année = NULL
// preinitialise l'horloge mets les valeurs lue précédement (à 0 si premier allumage)
setDateDs1307(int(second), int(minute), int(hour), int(dayOfWeek), int(dayOfMonth), int(month), int(year));
}
//***** LCD *****//
lcd.begin(20,4); // Initialise le LCD avec 20 colonnes x 4 lignes
delay(10); // pause rapide pour laisser temps initialisation
lcd.print("initialisation") ; // affiche la chaîne texte - message de test
lcd.setCursor(0, 1) ;
lcd.print("de l'horloge") ;
delay(2000); // pause de 2 secondes
lcd.clear(); // // efface écran et met le curseur en haut à gauche
delay(100); // pour laisser temps effacer écran
//**** liaison pour l'heure NTP ****//
Serial.println('A'); // envoi un "top" à Processing
while (millis()<5000) { // attente pendant 5 secondes d'une liaison série (ne fonctionne pas en dessous)
while (Serial.available()>0) { // tant qu'un octet est dans la liaison série
octetReception=Serial.read(); // Lit le 1er octet reçu et le met dans la variable
if (octetReception==13) { // si l'octet reçu est le retour chariot (CR ou 13)
// converti la chaine en entier pour les valeurs de temps
second = int((chaineReception.charAt(0)-48)*10)+int(chaineReception.charAt(1)-48) ;
minute = int((chaineReception.charAt(2)-48)*10)+int(chaineReception.charAt(3)-48);
hour = int((chaineReception.charAt(4)-48)*10)+int(chaineReception.charAt(5)-48);
dayOfWeek = 1;
dayOfMonth = int((chaineReception.charAt(6)-48)*10)+int(chaineReception.charAt(7)-48);
month = int((chaineReception.charAt(8)-48)*10)+int(chaineReception.charAt(9)-48);
year = int((chaineReception.charAt(12)-48)*10)+int(chaineReception.charAt(13)-48); //int((chaineReception.charAt(10)-48)*1000)+int((chaineReception.charAt(11)-48)*100)+
//mets le DS1307 en syncronisation avec l'horloge de l'ordinateur
setDateDs1307(int(second), int(minute), int(hour), int(dayOfWeek), int(dayOfMonth), int(month), int(year));
chaineReception=""; //RAZ de la chaine de réception
break; // sort de la boucle while
}
else { // si le caractère reçu n'est pas un saut de ligne
caractereRecu=char(octetReception); // convertit l'octet reçu en caractère
chaineReception=chaineReception+caractereRecu; // ajoute le caratère à la chaine
}
}
}
}
void loop(){
byte second, minute, hour, dayOfWeek, dayOfMonth, month, year;
getDateDs1307(&second, &minute, &hour, &dayOfWeek, &dayOfMonth, &month, &year);
if(second!=oldSecond){ // change l'affichage uniquement au changement de seconde
Serial.print(hour, DEC);
Serial.print(":");
Serial.print(minute, DEC);
Serial.print(":");
Serial.print(second, DEC);
Serial.print(" ");
Serial.print(month, DEC);
Serial.print("/");
Serial.print(dayOfMonth, DEC);
Serial.print("/");
Serial.print(year, DEC);
Serial.print(" Day_of_week:");
Serial.println(dayOfWeek, DEC);
lcd.home();
if (int(hour)<=9)lcd.print(0);
lcd.print(int(hour));
lcd.print (":");
if (int(minute)<=9)lcd.print(0);
lcd.print(int(minute));
lcd.print (":");
if (int(second)<=9)lcd.print(0);
lcd.print(int(second));
lcd.setCursor (0,1);
if (int(dayOfMonth)<=9)lcd.print(0);
lcd.print(int(dayOfMonth));
lcd.print ("/");
if (int(month)<=9)lcd.print(0);
lcd.print(int(month));
lcd.print ("/20");
lcd.print(int(year));
}
oldSecond=second; // réinitialise oldSecond
}