Go Down

Topic: Blink Error/Failure and Cnc_ctrl_V1 error messages (Read 236 times) previous topic - next topic

drewbriney

I'm struggling to get the Arduino running. I ran through the steps, setting up the board, port, etc., though none of the options were identical to any of the tutorials. There is no reset button on my Arduino that I can see. The green light is on. It doesn't blink.


Specs:
I'm using a macbook pro ios 10.14.6 and I uploaded the latest version of Arduino for Mac, including the update package referred to in the subject heading above. My board is Arduino Genuino Uno and my port is usbmodem145101. These were not on any instructions I saw, but they were the closest thing I could find to online instructions.


Blink Error Message[/u]
When I try to upload Blink, I get this error message:
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.


CNC_CTRL_V1 Error Message

When I try to upload the CNC file referred to above, I get this message:

Arduino: 1.8.10 (Mac OS X), Board: "Arduino/Genuino Uno"

sketch/System.cpp: In function 'void setPWMPrescalers(int)':
System.cpp:310:5: error: 'TCCR3B' was not declared in this scope
     TCCR3B &= ~prescalerEraser;   // this operation sets the three bits in TCCR3B to 0
     ^~~~~~
sketch/System.cpp:310:5: note: suggested alternative: 'TCCR0B'
     TCCR3B &= ~prescalerEraser;   // this operation sets the three bits in TCCR3B to 0
     ^~~~~~
     TCCR0B
System.cpp:311:5: error: 'TCCR4B' was not declared in this scope
     TCCR4B &= ~prescalerEraser;   // this operation sets the three bits in TCCR4B to 0
     ^~~~~~
sketch/System.cpp:311:5: note: suggested alternative: 'TCCR0B'
     TCCR4B &= ~prescalerEraser;   // this operation sets the three bits in TCCR4B to 0
     ^~~~~~
     TCCR0B
Multiple libraries were found for "Servo.h"
 Used: /Applications/Arduino.app/Contents/Java/libraries/Servo
Multiple libraries were found for "EEPROM.h"
 Used: /Applications/Arduino.app/Contents/Java/hardware/arduino/avr/libraries/EEPROM
exit status 1
'TCCR3B' was not declared in this scope

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

Maybe I missed the disclosure on the Maslow page, but no one told me I'd need a coding degree to get this thing running.

Lost,

Drew

pert

When I try to upload Blink, I get this error message:
Make sure you have selected the port of your Arduino board from the Tools > Port menu.

Sometimes the port will be labeled with the board name in the menu. Other times it will not. If you don't know which port is your Arduino, you can find it like this:
  • Unplug your Arduino board from the computer.
  • Tools > Port
  • Note the ports, if any, listed in the menu.
  • Close the Tools menu
  • Plug your Arduino board into the computer.
  • Tools > Port - The new port listed in the menu is your Arduino board.


When I try to upload the CNC file referred to above, I get this message:
These errors are because the code is written for a different microcontroller than the ATmega328P on the Uno you have, so the register names are different. It is possible that the CNC code is written so that you can configure it for different microcontrollers. We would need to look at the code to see whether that is the case. Please post a link to where you downloaded it from.

drewbriney

Thank you - I'll try the port thing. Checking on it without the Arduino in, I think I got the port correct. I'll post a follow-up after I get back to the shop.

Until then, this is the link I used to get the Arduino 1.8.10: https://www.arduino.cc/en/Main/Donate.
That doesn't look like the original link (I'm guessing it's a redirect link), so I copied the link URL from the previous page and that link (that took me to the donate page) was: https://www.arduino.cc/download_handler.php?f=/arduino-1.8.10-macosx.zip
That looks like a more helpful link.

If that link isn't good enough, please let me know.

drewbriney

Update: the usbmodem port was the correct port. The number at the end changed but the old number at the end was not available anymore.

drewbriney

I spoke with the manufacturers. I'm not certain that they read this post (I linked to it), but they suggested the arduino may be defective. Do you consider that a possibility or is this a coding issue?  Thank you in advance for your help.

pert

Do you get the same upload error if you are uploading to the Uno alone, with no wiring/shields/etc. connected to it?

drewbriney

Here is the error I get from the blink (when I am not connected to the arduino):

Arduino: 1.8.10 (Mac OS X), Board: "Arduino/Genuino Uno"

Sketch uses 924 bytes (2%) of program storage space. Maximum is 32256 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
An error occurred while uploading the sketch
avrdude: ser_open(): can't open device "/dev/cu.usbmodem146101": No such file or directory

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

Thank you for helping

pert

Make sure you have selected the port of your Arduino board from the Tools > Port menu.

Sometimes the port will be labeled with the board name in the menu. Other times it will not. If you don't know which port is your Arduino, you can find it like this:
  • Unplug your Arduino board from the computer.
  • Tools > Port
  • Note the ports, if any, listed in the menu.
  • Close the Tools menu
  • Plug your Arduino board into the computer.
  • Tools > Port - The new port listed in the menu is your Arduino board.

drewbriney

Someone told me this above - I did that - didn't have any trouble getting that figured out - but then I was told to try it without the arduino plugged in, so that is why I got the error and missing port.

Problem still exists.

pert


Go Up