avrdude: stk500_recv(): programmer is not responding

[pert]

avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x6a

Remove any connections to pins 0 and 1 on your Arduino board. These pins are used for communication with your computer, including uploads. Connecting anything to these pins can interfere with uploads.

Make sure you have the correct board selected from the Tools > Board menu.

Make sure you have selected the port of your Arduino board from the Tools > Port menu.

Sometimes the port will be labeled with the board name in the menu. Other times it will not. If you don't know which port is your Arduino board, you can find it like this:

• Unplug your Arduino board from the computer.
• Tools > Port
• Note the ports, if any, listed in the menu.
• Close the Tools menu. The ports list is only updated when the Tools menu is re-opened, so this step is essential.
• Plug your Arduino board into the computer.
• Tools > Port - The new port listed in the menu is your Arduino board.

[superwiku]

Arduino: 1.8.12 (Windows Store 1.8.33.0) (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)"

<Sketch uses 3418 bytes (11%) of program storage space. Maximum is 30720 bytes.
Global variables use 369 bytes (18%) of dynamic memory, leaving 1679 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: initialization failed, rc=-1
         Double check connections and try again, or use -F to override
         this check.

avrdude: stk500_recv(): programmer is not responding
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences./>

[nitran87700]

Select Arduino or file basis operating system you use and select preferences. Under preferences find "Proxy" and change the value to No Proxy. That fixes the communication error

[mohir]

Hello,
I have a very strange situation,
I fail to upload programs to my Uno boards, tried 2 different ones on 2 computers, all I get is 'programmer is not responding'. com port is fine. and I uploaded many times to uno boars before
to all other kinds of boards, Nano, ESP8266, and ESP32 all uploads without any problem.

please help
Regards

[pert]

I have a very strange situation,

Please do this:

• (In the Arduino IDE) File > Preferences
• Uncheck the checkbox next to "Show verbose output during: compilation"
• Check the checkbox next to "Show verbose output during: upload
• Click "OK"
• Sketch > Upload
• After the upload fails, you'll see a button on the right side of the orange bar "Copy error messages" (or the icon that looks like two pieces of paper at the top right corner of the black console window in the Arduino Web Editor). Click that button.
• In a forum reply here, click on the reply field.
• Click the </> button on the forum toolbar. This will add the forum's code tags markup to your reply.
• Press "Ctrl + V". This will paste the upload output between the code tags.
• Move the cursor outside of the code tags before you add any additional text to your reply.

[mohir]

Thank you,
now it got even stranger,
the problem disappeared, on both computers,
really don't know what was going on.
Thanks again

[pert]

You're welcome. I'm just glad to hear that it's working for you now. Certainly none of my instructions would be expected to fix the problem. They were only intended to get information that could be used to diagnose the issue.

[kaspiuxz]

Hello, i just got my arduino nano 3.0. Tried first time to upload and this happened:
Arduino: 1.8.12 (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)"

Sketch uses 924 bytes (3%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x94
Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x94
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x94

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.

[pert]

Select Tools > Processor > ATmega328P and then try uploading again.

[kaspiuxz]

All the same

[pert]

Remove any connections to pins 0 and 1 on your Arduino board. These pins are used for communication with your computer, including uploads. Connecting anything to these pins can interfere with uploads.

Make sure you have the correct board selected from the Tools > Board menu. Note that there are multiple boards with "Nano" in their name. The board you have selected in the Arduino IDE's menu is for the classic Nano. If you have a Nano 33 IoT, Nano Every, or Nano 33 BLE, you need a different board selection.

Make sure you have selected the port of your Arduino board from the Tools > Port menu.

Sometimes the port will be labeled with the board name in the menu. Other times it will not. If you don't know which port is your Arduino board, you can find it like this:

• Unplug your Arduino board from the computer.
• Tools > Port
• Note the ports, if any, listed in the menu.
• Close the Tools menu. The ports list is only updated when the Tools menu is re-opened, so this step is essential.
• Plug your Arduino board into the computer.
• Tools > Port - The new port listed in the menu is your Arduino board.

[forbrains]

Under-voltage.

Check the voltage on RAW & VCC.

You'll get this is your voltage drops to 4.6v during the Write / verification Read phases.

It's common if using a USB to TTL adapter to see the voltage drop too much when programming the chip.

[wooyoungyoon]

Code: [Select]

Arduino: 1.8.12 (Windows 10), Board: "Arduino Nano, ATmega328P (Old Bootloader)"

Sketch uses 924 bytes (3%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM5 -b57600 -D -Uflash:w:C:\Users\v-woyoon\AppData\Local\Temp\arduino_build_86211/sketch_jun01b.ino.hex:i

avrdude: Version 6.3-20190619
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM5
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x39
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x39

avrdude done.  Thank you.

Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.


[pert]

Code: [Select]

avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x39

Select Tools > Processor > ATmega328P and then try uploading again.

[lucaf69]

Arduino:1.8.12 (Windows 10), Scheda:"Anet V1.0"

Lo sketch usa 111980 byte (88%) dello spazio disponibile per i programmi. Il massimo è 126976 byte.
Le variabili globali usano 4511 byte di memoria dinamica.
C:\Program Files (x86)\Arduino\hardware\tools\avr/bin/avrdude -CC:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf -v -patmega1284p -carduino -PCOM3 -b57600 -D -Uflash:w:C:\Users\Luca\AppData\Local\Temp\arduino_build_67896/Marlin.ino.hex:i

avrdude: Version 6.3-20190619
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM3
         Using Programmer              : arduino
         Overriding Baud Rate          : 57600
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xc8
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xc8

avrdude done.  Thank you.

Problema di caricamento sulla scheda. Guarda http://www.arduino.cc/en/Guide/Troubleshooting#upload per suggerimenti

I have tried everything found on the net to solve this problem but I have not had any results
Can anyone help me
i am trying to mount the marlin 1.1.9 on my anet a6
the motherboard was just repaired with the replacement of the processor that had burned out.

Thank you.