Go Down

Topic: Uploading Issues (Read 187 times) previous topic - next topic

fardinho21

Hello,

I am having issues with uploading to my Arduino.
I have tried the suggestions on the Arduino's troubleshooting webpage and I am still getting the same problem. I have tried many solutions posted online. I have tried two different boards (Nano and Uno) I get the same problem.

Pasted below is the error message I get. My OS information is also below.

Thanks in advance for the help.

Code: [Select]
Sketch uses 444 bytes (1%) of program storage space. Maximum is 30720 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
/home/maj/Desktop/arduino-1.8.9/hardware/tools/avr/bin/avrdude -C/home/maj/Desktop/arduino-1.8.9/hardware/tools/avr/etc/avrdude.conf -v -patmega328p -carduino -P/dev/ttyUSB0 -b115200 -D -Uflash:w:/tmp/arduino_build_125877/sketch_may14a.ino.hex:i

avrdude: Version 6.3-20171130
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "/home/maj/Desktop/arduino-1.8.9/hardware/tools/avr/etc/avrdude.conf"
         User configuration file is "/home/maj/.avrduderc"
         User configuration file does not exist or is not a regular file, skipping

         Using Port                    : /dev/ttyUSB0
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x00
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x00

avrdude done.  Thank you.

Problem uploading to board.  See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.


Code: [Select]
[maj ~ 09:56 PM] :  >lsb_release -a
No LSB modules are available.
Distributor ID: LinuxMint
Description: Linux Mint 19.1 Tessa
Release: 19.1
Codename: tessa

arijitkrhaldar

If you haven't yet figured the problem out...can you just plug in an LED between the RESET pin and GND, and check what happens when you press upload? Reset circuitry might be the issue..or, did you make any changes in the avrdude configuration file?

Go Up