Go Down

Topic: Global Server (Read 71 times) previous topic - next topic


Hi every one,

I'm new in arduino world and this is my first project.
The objectif is check from a web page if a vehicle is in the garage or not.

The sensor part of my code is okk and I can see the statue on a local server but i need hep to do the same on a global server.
Code: [Select]
/*Test version
 * If input return a certain value
 * send to server that the ambulance is here
 * else send to the server that the ambulance is away

#include <SPI.h>
#include <WiFiNINA.h>

#include "arduino_secrets.h"
//enter your sensitive data in the Secret tab/arduino_secrets.h
char ssid[] = SECRET_SSID;        // your network SSID (name)
char pass[] = SECRET_PASS;    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;                 // your network key index number (needed only for WEP)

int status = WL_IDLE_STATUS;
WiFiServer server(80);

void setup() {
  // put your setup code here, to run once:
   pinMode(A0, INPUT);
  // initialize digital pin LED_BUILTIN as an output
  // initialize serial communication at 9600 bits per second:

// check for the WiFi module:
  if (WiFi.status() == WL_NO_MODULE) {
    Serial.println("Communication with WiFi module failed!");
    // don't continue
    while (true);

  String fv = WiFi.firmwareVersion();
    Serial.println("Please upgrade the firmware");

  // attempt to connect to WiFi network:
  while (status != WL_CONNECTED) {
    Serial.print("Attempting to connect to Network named: ");
    Serial.println(ssid);                   // print the network name (SSID);

    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:
    status = WiFi.begin(ssid, pass);
    // wait 10 seconds for connection:
  server.begin();                           // start the web server on port 80
  printWifiStatus();                        // you're connected now, so print out the status

void loop() {
  // put your main code here, to run repeatedly:
 int sensorValue = analogRead(A0); // read the input on analog pin 0
 delay(1000); // delay in between reads for stability (ou faut il mettre le delay?)
  // print out the value you read:
if (sensorValue >= 150)
digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltage level)
digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW

WiFiClient client = server.available();   // listen for incoming clients

  if (client) {                             // if you get a client,
    Serial.println("new client");           // print a message out the serial port
    String currentLine = "";                // make a String to hold incoming data from the client
    while (client.connected()) {            // loop while the client's connected
      if (client.available()) {             // if there's bytes to read from the client,
        char c = client.read();             // read a byte, then
        Serial.write(c);                    // print it out the serial monitor
        if (c == '\n') {                    // if the byte is a newline character

          // if the current line is blank, you got two newline characters in a row.
          // that's the end of the client HTTP request, so send a response:
          if (currentLine.length() == 0) {
            // HTTP headers always start with a response code (e.g. HTTP/1.1 200 OK)
            // and a content-type so the client knows what's coming, then a blank line:
            client.println("HTTP/1.1 200 OK");

            client.print("est ce que l'ambulance est là?");
            if (sensorValue >= 150)
            // the content of the HTTP response follows the header:

            // The HTTP response ends with another blank line:
            // break out of the while loop:
          } else {    // if you got a newline, then clear currentLine:
            currentLine = "";
        } else if (c != '\r') {  // if you got anything else but a carriage return character,
          currentLine += c;      // add it to the end of the currentLine
    // close the connection:
    Serial.println("client disconnected");

void printWifiStatus() {
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");

  // print your board's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.println(" dBm");
  // print where to go in a browser:
  Serial.print("To see this page in action, open a browser to http://");

thank's a lot if somebody can help me

(and sorry for my bad english I'm from switzerland)

Go Up