AES128 implementation (AddRoundKey + SubBytes) on Arduino Nano

Using Arduino Programming Questions
1

Hello,
Could please anyone look at the code below and tell me it's ok.
#include <Crypto.h>
#include <AES.h>
#include <string.h>

// plainText[16] contains the text we need to encrypt
byte plainText[16]= {00, 11, 22, 33, 44, 55, 66, 77, 88, 99, 01, 02, 03, 04, 05, 06};
// key[16] contains the 16-byte key for encryption
byte key[16];
// S-box values
byte s[256] = {
0x63, 0x7C, 0x77, 0x7B, 0xF2, 0x6B, 0x6F, 0xC5, 0x30, 0x01, 0x67, 0x2B, 0xFE, 0xD7, 0xAB, 0x76,
0xCA, 0x82, 0xC9, 0x7D, 0xFA, 0x59, 0x47, 0xF0, 0xAD, 0xD4, 0xA2, 0xAF, 0x9C, 0xA4, 0x72, 0xC0,
0xB7, 0xFD, 0x93, 0x26, 0x36, 0x3F, 0xF7, 0xCC, 0x34, 0xA5, 0xE5, 0xF1, 0x71, 0xD8, 0x31, 0x15,
0x04, 0xC7, 0x23, 0xC3, 0x18, 0x96, 0x05, 0x9A, 0x07, 0x12, 0x80, 0xE2, 0xEB, 0x27, 0xB2, 0x75,
0x09, 0x83, 0x2C, 0x1A, 0x1B, 0x6E, 0x5A, 0xA0, 0x52, 0x3B, 0xD6, 0xB3, 0x29, 0xE3, 0x2F, 0x84,
0x53, 0xD1, 0x00, 0xED, 0x20, 0xFC, 0xB1, 0x5B, 0x6A, 0xCB, 0xBE, 0x39, 0x4A, 0x4C, 0x58, 0xCF,
0xD0, 0xEF, 0xAA, 0xFB, 0x43, 0x4D, 0x33, 0x85, 0x45, 0xF9, 0x02, 0x7F, 0x50, 0x3C, 0x9F, 0xA8,
0x51, 0xA3, 0x40, 0x8F, 0x92, 0x9D, 0x38, 0xF5, 0xBC, 0xB6, 0xDA, 0x21, 0x10, 0xFF, 0xF3, 0xD2,
0xCD, 0x0C, 0x13, 0xEC, 0x5F, 0x97, 0x44, 0x17, 0xC4, 0xA7, 0x7E, 0x3D, 0x64, 0x5D, 0x19, 0x73,
0x60, 0x81, 0x4F, 0xDC, 0x22, 0x2A, 0x90, 0x88, 0x46, 0xEE, 0xB8, 0x14, 0xDE, 0x5E, 0x0B, 0xDB,
0xE0, 0x32, 0x3A, 0x0A, 0x49, 0x06, 0x24, 0x5C, 0xC2, 0xD3, 0xAC, 0x62, 0x91, 0x95, 0xE4, 0x79,
0xE7, 0xC8, 0x37, 0x6D, 0x8D, 0xD5, 0x4E, 0xA9, 0x6C, 0x56, 0xF4, 0xEA, 0x65, 0x7A, 0xAE, 0x08,
0xBA, 0x78, 0x25, 0x2E, 0x1C, 0xA6, 0xB4, 0xC6, 0xE8, 0xDD, 0x74, 0x1F, 0x4B, 0xBD, 0x8B, 0x8A,
0x70, 0x3E, 0xB5, 0x66, 0x48, 0x03, 0xF6, 0x0E, 0x61, 0x35, 0x57, 0xB9, 0x86, 0xC1, 0x1D, 0x9E,
0xE1, 0xF8, 0x98, 0x11, 0x69, 0xD9, 0x8E, 0x94, 0x9B, 0x1E, 0x87, 0xE9, 0xCE, 0x55, 0x28, 0xDF,
0x8C, 0xA1, 0x89, 0x0D, 0xBF, 0xE6, 0x42, 0x68, 0x41, 0x99, 0x2D, 0x0F, 0xB0, 0x54, 0xBB, 0x16
};
byte sbox_lookup [16];

void setup() {
// put your setup code here, to run once:

Serial.begin(9600);
pinMode(13,OUTPUT);

for (int i = 0; i < 9; i++){
delay(500);
digitalWrite (13, HIGH);
}

for (int j = 0; j < 15; j++){
		sbox_lookup[j] = s[plainText[j]^key[j]];
  digitalWrite (13, LOW);

}
}

void loop() {
// put your main code here, to run repeatedly:

}

2

What do you try to achieve here?

First you set to the pin HIGH level 9 times, without set it LOW.
Than you set it LOW 15 times...
Neither of them make any sense

3

Hi, what I am trying to achieve is to run AddRoundKey and SubBytes on the chip.

The sample code I took looked like:

set plainText to a known value
for i 0 to 9:
delay 500 set LED 13 to HIGH
for j 0 to 15:
sbox_lookup[j] = s[plainText[j] XOR key[j]]
set LED 13 to LOW

What the code creators were trying to achieve here were:
run AddRoundKey and SubBytes against a known plaintext value 10 times (to average them then). Triggering and capturing of the power trace is achieved by monitoring port 13 on the Arduino which is set to high when the cryptographic functions are running.

4

This is a exact calculations, it give you exact the same results every times. What is the point to average them?

Setting pin to HIGH many times without return it to LOW is useless.
Whole the code is something non-sense.

5

This topic was automatically closed 180 days after the last reply. New replies are no longer allowed.