Arduino Nano and nRF24L01

I am trying to use two nRF24L01 transceivers to communicate between 2 Nanos but I just can't get them working.

I followed this tutorial: https://arduino-info.wikispaces.com/Nrf24L01-2.4GHz-HowTo. I have checked wiring like 10 times so that isn't a problem. Tested them with 1, 10 and 100uF capacitors, still no help.

This is what serial monitor shows:

RF24/examples/GettingStarted/
ROLE: Pong back
*** PRESS 'T' to begin transmitting to the other node
STATUS = 0x00 RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=0 TX_FULL=0
RX_ADDR_P0-1 = 0x0000000000 0x0000000000
RX_ADDR_P2-5 = 0x00 0x00 0x00 0x00
TX_ADDR = 0xffffffffff
RX_PW_P0-6 = 0x00 0x00 0x00 0x00 0x00 0x00
EN_AA = 0x00
EN_RXADDR = 0x00
RF_CH = 0xce
RF_SETUP = 0xff
CONFIG = 0xff
DYNPD/FEATURE = 0x00 0x00
Data Rate = 1MBPS
Model = nRF24L01
CRC Length = Disabled
PA Power = PA_MIN
Got payload 4294967103...Sent response.
Got payload 4294967167...Sent response.

Attached ground and 3.3v to another Nano and then I got this:

RF24/examples/GettingStarted/
ROLE: Pong back
*** PRESS 'T' to begin transmitting to the other node
STATUS = 0x00 RX_DR=0 TX_DS=0 MAX_RT=0 RX_P_NO=0 TX_FULL=0
RX_ADDR_P0-1 = 0x0000000000 0x0000000000
RX_ADDR_P2-5 = 0x00 0x00 0x00 0x00
TX_ADDR = 0xffffffffff
RX_PW_P0-6 = 0xff 0x7f 0x00 0x00 0x00 0x00
EN_AA = 0x00
EN_RXADDR = 0x00
RF_CH = 0xce
RF_SETUP = 0xff
CONFIG = 0xff
DYNPD/FEATURE = 0x00 0x00
Data Rate = 1MBPS
Model = nRF24L01
CRC Length = Disabled
PA Power = PA_HIGH
Got payload 4294967295...Sent response.
Got payload 4294967295...Sent response.

Can anyone help me?

kazzka:
Got payload 4294967103…Sent response.
Got payload 4294967167…Sent response.

Got payload 4294967295…Sent response.
Got payload 4294967295…Sent response.

Doesn’t the above mean it is working?
Each Nano is telling u that it received a payload and it sent a response.

No. Other Nano wasn't even connected.

kazzka:
No. Other Nano wasn't even connected.

Ah yes and we would all have known that by looking into our little magic bowls.....

You should FULLY describe your setup and the actual issues you are having and not expect anyone to guess what u have going on.

So what happens when u have both Nanos connected?
Your actual code and photos of your connections might elicit more help from board members.

All those zeros should give the idea that there is something wrong with communication between Arduino and transceiver.

I have uploaded non modified GettingStarted sketch and believe me, the connections are 100% correct.

What's the point of posting output of an incomplete setup?

Since you can't be bothered to provide additional info as suggested, why don't u first try the code provided with the tutorial.

Here is a video covering it which you can also.

It uses an Uno and a Nano, but 2 Nanos should be no problem.

have you tried mirf lib?