When I do this no errors in the format are detected. though now an error 2:29 occurs now when I try to verify the code.
Rocket_Launcher_updated_2 2:29 : error expected ';' before 'mySerialPort'
MySerialPort.write(0x10); // turn on the colon ":"
^
exit status1
Yes I fixed the missing brackets.
#define FuseTIME 1500 //Fuse current duration in milliseconds.
#include <SoftwareSerial.h> //Call the SoftwareSerial library.
#define Fuse 7 //Pin connected to the Fuse (your LED or igniter)
#define GoButt 6 //Pin connected to the GO button
#define ArmButt 5 //Pin connected to the ARM button
#define BuzzPin 4 //Connected to the buzzer
#define TXdata 3 //Conneted to Rx of the Display
#define RXdata 2 //not used
#define SetPot 0 //Analog Pin connected to the Potentiometer
SoftwareSerial mySerialPort(RXdata, TXdata);
void setup() {
pinMode(TXdata, OUTPUT);
pinMode(RXdata, INPUT);
pinMode(Fuse, OUTPUT);
pinMode(ArmButt, INPUT); // set "ARM" button pin to input
pinMode(GoButt, INPUT); // set "GO" button pin to input
digitalWrite(Fuse, LOW); // OPEN the fuse circuit.
digitalWrite(ArmButt, HIGH); // turn on pull up resistor
digitalWrite(GoButt, HIGH); // turn on pull up resistor
mySerialPort.begin(9600);
delay(10); // Wait for Serial Display start up
mySerialPort.print("v") // Reset the display
mySerialPort.print("z") // Brightness
mySerialPort.write(0x40); // 3/4 Intensity
mySerialPort.print("w") // Decimal Point Control
mySerialPort.write(0x10); // turn on the colon ":"
}
int DownCntr; // down counter (1/10 Secs)
int Go = 0; // Stopped
void loop() {
if (!digitalRead(GoButt) || !digitalRead(ArmButt)) {
Go = 0; // Stops the countdown
tone(BuzzPin, 440, 1500);
delay(1500);
}
if (Go == 0) {
WaitARM();
WaitGO();
}
ShowTimer();
if (DownCntr > 50) {
if (DownCntr % 10 == 0)tone(BuzzPin, 1000, 50); // Beeps every second
}
else if (DownCntr % 2 == 0)tone(BuzzPin, 1000, 50); // Beep goes faster
if (DownCntr == 0) {
tone(BuzzPin, 440, FuseTIME); // Launch tone
digitalWrite(Fuse, HIGH); // CLOSE the fuse circuit
delay(FuseTIME);
digitalWrite(Fuse, LOW); // OPEN the fuse circuit
Go = 0;
}
while (millis() % 100); // wait for a moment
delay(50);
DownCntr--;
}
void WaitGO() {
ShowTimer();
while (digitalRead(GoButt));
Go = 1;
delay(20);
while (!digitalRead(GoButt)); // Debounce the GO button
}
void ReadTimer() {
DownCntr = map(analogRead(SetPot), 0, 1023, 5, 60);
DownCntr *= 10;
}
void ShowTimer() {
String seconds = String (DownCntr, DEC);
while (seconds.length() < 3)seconds = "0" + seconds; // format to 3 numbers
mySerialPort.print(seconds); // Write to Display
mySerialPort.print(" "); // Last digit switched off
}
void WaitARM() {
while (digitalRead(ArmButt) == 1) {
ReadTimer();
delay(50);
ReadTimer();
ShowTimer();
delay(150);
}
Go = 0;
ShowTimer();
tone(BuzzPin, 2000, 150);
delay(200);
tone(BuzzPin, 2000, 150);
delay(200);
tone(BuzzPin, 2000, 150);
delay(20);
while (!digitalRead(ArmButt)); // Debounce the ARM button
}