Arduino Uno R3 with ENC28J60 Ethernet modules

system · September 30, 2013, 11:49am

Hello friend,

Is it possible to connect Arduino Uno R3 with ENC28J60 Ethernet modules if yes then please guide me about PIN to be connected

Waiting for a reply

thank you

system · September 30, 2013, 12:35pm

Yes, but the ENC28J60 is not officially supported.
If your module doesn't have a 3.3V regulator, you can use the 3.3V of the Arduino board.
The connections are with SPI interface. So the pins are fixed, only the /CS can be choosen by yourself.

Which library do you want to use ?

system · September 30, 2013, 12:54pm

Caltoa:
Yes, but the ENC28J60 is not officially supported.
If your module doesn't have a 3.3V regulator, you can use the 3.3V of the Arduino board.
The connections are with SPI interface. So the pins are fixed, only the /CS can be choosen by yourself.

Which library do you want to use ?

Boss I am very new with arduino. I just have 3 thing

Arduino uno r3
ENC28J60 Ethernet modules
8 Channel Relay Board

Now i want 8 buttons on webpage so that i can turn off/on relays from remote location.

like this youtube video

i don't know how to connect by wire with each other. even i don't know how to programmed them

Please help me. plz, plz, plz, plz, plz, plz,

system · September 30, 2013, 5:01pm

Sorry to disappoint you, but it is not that easy.

With the Arduino Ethernet Shield you can use all the examples and we are willing to help on this forum.

But the ENC28J60 is not officially supported as I wrote.
However, some made a library for it. But finding a good and up-to-date library is not easy.

The YouTube movie points to the sketch.
Did you see the link to the sketch: InternetFido.com
That sketch lacks good explanation.
I think the sketch uses this library: arduino-projects/libraries at master · muanis/arduino-projects · GitHub
But I'm not sure.
The WebRemote example for that library, shows buttons that can be clicked.
arduino-projects/WebRemote.pde at master · muanis/arduino-projects · GitHub

Using the ENC28J60 is something for advanced users.
The table on this page show how to connect the Uno:
http://www.geeetech.com/wiki/index.php/Arduino_ENC28J60_Ethernet_Module
The CS is connected to D10. Perhaps the library uses another pin for CS, or perhaps you have to adapt the library.

If you buy an Arduino Ethernet Shield, you can start with a webpage example, and add the buttons to that example.

system · September 30, 2013, 5:34pm

Caltoa:
Sorry to disappoint you, but it is not that easy.

With the Arduino Ethernet Shield you can use all the examples and we are willing to help on this forum.
http://arduino.cc/en/Main/ArduinoEthernetShield

But the ENC28J60 is not officially supported as I wrote.
However, some made a library for it. But finding a good and up-to-date library is not easy.

The YouTube movie points to the sketch.
Did you see the link to the sketch: InternetFido.com
That sketch lacks good explanation.
I think the sketch uses this library: arduino-projects/libraries at master · muanis/arduino-projects · GitHub
But I'm not sure.
The WebRemote example for that library, shows buttons that can be clicked.
arduino-projects/libraries/ETHER_28J60/examples/WebRemote/WebRemote.pde at master · muanis/arduino-projects · GitHub

Using the ENC28J60 is something for advanced users.
The table on this page show how to connect the Uno:
http://www.geeetech.com/wiki/index.php/Arduino_ENC28J60_Ethernet_Module
The CS is connected to D10. Perhaps the library uses another pin for CS, or perhaps you have to adapt the library.

If you buy an Arduino Ethernet Shield, you can start with a webpage example, and add the buttons to that example.

thank you for your help.
I could not do it. its not so much easy for me so i have ordered Ethernet Shield in ebay. now can you help to do the same thing with Arduino Ethernet Shield please include the web server pages also

thanks again for your help

system · October 1, 2013, 2:58am

In the Arduino IDE are examples.
One of the examples for the "Ethernet" library is the "WebServer".
It is also online: http://arduino.cc/en/Tutorial/WebServer

The Ethernet library can do DHCP.
This line: Ethernet.begin(mac, ip);
uses a fixed ip address.
You can use DHCP by omitting the ip, like this: Ethernet.begin(mac);

With DHCP the router creates and ip number for the Arduino, and that ip number is written to the serial monitor, so you know what to type in the browser.
For example if the router assigns ip number: 192,168,1,3
you type in the browser: http://192.168.1.3

system · October 3, 2013, 8:59am

Caltoa:
Sorry to disappoint you, but it is not that easy.

With the Arduino Ethernet Shield you can use all the examples and we are willing to help on this forum.
http://arduino.cc/en/Main/ArduinoEthernetShield

But the ENC28J60 is not officially supported as I wrote.
However, some made a library for it. But finding a good and up-to-date library is not easy.

The YouTube movie points to the sketch.
Did you see the link to the sketch: InternetFido.com
That sketch lacks good explanation.
I think the sketch uses this library: arduino-projects/libraries at master · muanis/arduino-projects · GitHub
But I'm not sure.
The WebRemote example for that library, shows buttons that can be clicked.
arduino-projects/libraries/ETHER_28J60/examples/WebRemote/WebRemote.pde at master · muanis/arduino-projects · GitHub

Using the ENC28J60 is something for advanced users.
The table on this page show how to connect the Uno:
http://www.geeetech.com/wiki/index.php/Arduino_ENC28J60_Ethernet_Module
The CS is connected to D10. Perhaps the library uses another pin for CS, or perhaps you have to adapt the library.

If you buy an Arduino Ethernet Shield, you can start with a webpage example, and add the buttons to that example.

Hello Sir,

i have manage to connect ENC28J60 Ethernet modules and i am using the following code

// A simple web server

#include "etherShield.h"
#include "ETHER_28J60.h"

int outputPin = 6;

static uint8_t mac[6] = {0x54, 0x55, 0x58, 0x10, 0x00, 0x24}; // this just needs to be unique for your network,
static uint8_t ip[4] = {192, 168, 1, 10}; // the IP address for your board. Check your home hub
static uint16_t port = 80; // Use port 80 - the standard for HTTP
ETHER_28J60 e;
void setup()
{
e.setup(mac, ip, port);
pinMode(outputPin, OUTPUT);
}
void loop()
{
char* params;
if (params = e.serviceRequest())
{
e.print("");
e.print("

Web Remote

");
e.print("Relay 1 : Turn on / Turn off / Reboot
");
e.print("Relay 2 : Turn on / Turn off / Reboot
");
e.print("Relay 3 : Turn on / Turn off / Reboot
");
e.print("Relay 4 : Turn on / Turn off / Reboot
");

if (strcmp(params, "?r1=on") == 0)
{ digitalWrite(3, HIGH); }
else if (strcmp(params, "?r1=off") == 0) // Modified -
{ digitalWrite(3, LOW); }
else if (strcmp(params, "?r1=reboot") == 0) // Modified r
{ digitalWrite(3, HIGH);
delay(1000);
digitalWrite(3, LOW);
}

if (strcmp(params, "?r2=on") == 0)
{ digitalWrite(4, HIGH); }
else if (strcmp(params, "?r2=off") == 0) // Modified -
{ digitalWrite(4, LOW); }
else if (strcmp(params, "?r2=reboot") == 0) // Modified -
{ digitalWrite(4, HIGH);
delay(1000);
digitalWrite(4, LOW);
}

if (strcmp(params, "?r3=on") == 0)
{ digitalWrite(5, HIGH); }
else if (strcmp(params, "?r3=off") == 0) // Modified -
{ digitalWrite(5, LOW); }
else if (strcmp(params, "?r3=reboot") == 0) // Modified --
{ digitalWrite(5, HIGH);
delay(1000);
digitalWrite(5, LOW);
}

if (strcmp(params, "?r4=on") == 0)
{ digitalWrite(6, HIGH); }
else if (strcmp(params, "?r4=off") == 0) // Modified --
{ digitalWrite(6, LOW); }
else if (strcmp(params, "?r4=reboot") == 0) // Modified --
{ digitalWrite(6, HIGH);
delay(1000);
digitalWrite(6, LOW);
}

e.respond();
}
}

but getting error

200 OK
A

I can not run 8 relay only 3 relay is working but when i am adding 4th relay code getting this error can please tell me where is the problem.

system · October 3, 2013, 9:46am

but getting error

200 OK
A

Doesn't look like an error to me. Why do you think it is?

i am using the following code

Which looks like crap, and is improperly posted. Nothing goes on the line after the }. Every } goes on a new line. Use Tools + Auto Format before you think of posting code again. When you do, use the # icon to generate code tags FIRST.

I can not run 8 relay only 3 relay is working but when i am adding 4th relay code getting this error can please tell me where is the problem

In your code. It looks to me like you are using too much SRAM. Check that possibility out:
http://playground.arduino.cc/Code/AvailableMemory

system · October 3, 2013, 4:13pm

Hello Sir,

I am very very sorry for my mistake can you now check the code for me.

// A simple web server

#include "etherShield.h"
#include "ETHER_28J60.h"

int outputPin = 6;

static uint8_t mac[6] = {0x54, 0x55, 0x58, 0x10, 0x00, 0x24};   // this just needs to be unique for your network,                                                         
static uint8_t ip[4] = {192, 168, 1, 10};                       // the IP address for your board. Check your home hub
static uint16_t port = 80;                                      // Use port 80 - the standard for HTTP
ETHER_28J60 e;
void setup()
{ 
  e.setup(mac, ip, port);
  pinMode(outputPin, OUTPUT);
}
void loop()
{
  char* params;
  if (params = e.serviceRequest())
  {
    e.print("<center>");
    e.print("<H1>Web Remote</H1>");
    e.print("Relay 1 : <A HREF='?r1=on'>Turn on</A> / <A HREF='?r1=off'>Turn off</A> / <A HREF='?r1=reboot'>Reboot</A>
");
    e.print("Relay 2 : <A HREF='?r2=on'>Turn on</A> / <A HREF='?r2=off'>Turn off</A> / <A HREF='?r2=reboot'>Reboot</A>
");
    e.print("Relay 3 : <A HREF='?r3=on'>Turn on</A> / <A HREF='?r3=off'>Turn off</A> / <A HREF='?r3=reboot'>Reboot</A>
");
    e.print("Relay 4 : <A HREF='?r4=on'>Turn on</A> / <A HREF='?r4=off'>Turn off</A> / <A HREF='?r4=reboot'>Reboot</A>
");

    
    if (strcmp(params, "?r1=on") == 0)
    { digitalWrite(3, HIGH); }
    else if (strcmp(params, "?r1=off") == 0) // Modified -
    { digitalWrite(3, LOW);  }
    else if (strcmp(params, "?r1=reboot") == 0) // Modified r
    { digitalWrite(3, HIGH); 
      delay(1000); 
      digitalWrite(3, LOW);
    }
    
    if (strcmp(params, "?r2=on") == 0)
    { digitalWrite(4, HIGH); }
    else if (strcmp(params, "?r2=off") == 0) // Modified -
    { digitalWrite(4, LOW);  }
    else if (strcmp(params, "?r2=reboot") == 0) // Modified -
    { digitalWrite(4, HIGH); 
      delay(1000); 
      digitalWrite(4, LOW);
    }
    
    
         if (strcmp(params, "?r3=on") == 0)
    { digitalWrite(5, HIGH); }
    else if (strcmp(params, "?r3=off") == 0) // Modified -
    { digitalWrite(5, LOW);  }
    else if (strcmp(params, "?r3=reboot") == 0) // Modified --
    { digitalWrite(5, HIGH); 
      delay(1000); 
      digitalWrite(5, LOW);
    }
    
    
             if (strcmp(params, "?r4=on") == 0)
    { digitalWrite(6, HIGH); }
    else if (strcmp(params, "?r4=off") == 0) // Modified --
    { digitalWrite(6, LOW);  }
    else if (strcmp(params, "?r4=reboot") == 0) // Modified --
    { digitalWrite(6, HIGH); 
      delay(1000); 
      digitalWrite(6, LOW);
    }
      
    e.respond();
  }
}

system · October 21, 2013, 1:49pm

Caltoa:
With the Arduino Ethernet Shield you can use all the examples and we are willing to help on this forum.
http://arduino.cc/en/Main/ArduinoEthernetShield
But the ENC28J60 is not officially supported as I wrote.

While not officially supported you can use this library that implements the same API als the original Ethernet-library and can run the examples that come with the IDE by changing the include of Ethernet.h to UIPEthernet.h:

Norbert

system · June 11, 2014, 4:08am

san2roy:
Hello friend,

Is it possible to connect Arduino Uno R3 with ENC28J60 Ethernet modules if yes then please guide me about PIN to be connected

Waiting for a reply

thank you

yes I have done it

stevech · June 11, 2014, 6:22am

Consider too the much newer and much better ethernet interface: Wiznet's 820io.

Topic		Replies	Views
Connection scheme enc28j60 - Arduino uno rev 3 Networking, Protocols, and Devices	2	1407	May 6, 2021
Will this ethernet module work for Arduino UNO? General Electronics	10	3253	May 6, 2021
I want to connect the Enc28J60 module with arduino Uno Board Networking, Protocols, and Devices	1	1443	May 6, 2021
Can't get ENC28J60 Module to work Networking, Protocols, and Devices	3	1030	May 6, 2021
Ethernet ENC28J60 problem Networking, Protocols, and Devices	2	2119	May 6, 2021

Arduino Uno R3 with ENC28J60 Ethernet modules

Web Remote

Related topics