Atmega328P fuse read error?

Other Hardware 3rd Party Boards
1

Hi, I was wanting to check the fuses using Avrdude (5.10), but kept getting 0x0:

avrdude -c arduino -p m328p -P COM9 -U lfuse:r:-:h

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x1e950f
avrdude: reading lfuse memory:

Reading | ################################################## | 100% 0.00s

avrdude: writing output file "<stdout>"
0x0

avrdude: safemode: Fuses OK

avrdude done.  Thank you.

I have used both my laptop and computer, checked the port was definately correct, and can seem to read the signature byte but not any fuses or lock bits. I tried to use verbose output and got:

avrdude -c arduino -p m328p -P COM9 -v

avrdude: Version 5.10, compiled on Jan 19 2010 at 10:45:23
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2009 Joerg Wunsch

         System wide configuration file is "C:\WinAVR-20100110\bin\avrdude.conf"

         Using Port                    : COM9
         Using Programmer              : arduino
         AVR Part                      : ATMEGA328P
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PC2
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :

                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom        65     5     4    0 no       1024    4      0  3600  3600 0xff 0xff
           flash         65     6   128    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           efuse          0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           lock           0     0     0    0 no          1    0      0  4500  4500 0x00 0x00
           calibration    0     0     0    0 no          1    0      0     0     0 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00

         Programmer Type : Arduino
         Description     : Arduino
         Hardware Version: 3
         Firmware Version: 3.3
         Vtarget         : 0.3 V
         Varef           : 0.3 V
         Oscillator      : 28.800 kHz
         SCK period      : 3.3 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e950f
avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0

avrdude: safemode: lfuse reads as 0
avrdude: safemode: hfuse reads as 0
avrdude: safemode: efuse reads as 0
avrdude: safemode: Fuses OK

avrdude done.  Thank you.

I am able to download hex files to the atmega328P but just can't seem to check the fuse settings. I am fairly sure that 0x00 for efuse is impossible...

Thanks alot

2

The bootloader does not support reading (or writing) the fuses.

3

Ah. ok, thanks alot

4

And the bootloader doesn't even support reading the actual device signature: the value you get is built into the bootloader.

5

Try code here for downloading a bootloader via bitbang - I don't know enough to say if it will work on other than a duemilanove with jumpers from X3 to the ICSP header tho ...

http://www.geocities.jp/arduino_diecimila/bootloader/index_en.html