Atmega328p sketch upload issue

Using Arduino Avrdude, stk500, Bootloader issues
1

I recently purchase a few atmega328p chips, I have successfully upload the optiboot uno bootloader to theses ic's, but now I am not able to upload the blink sketch, any help will be appreciated. Im not sure how to attach program code samples or the like, so im attaching the verbose compiler output that shows when i try to upoad the sketch.

System wide configuration file is "C:\Documents and Settings\Owner\Local Settings\Application Data\Arduino15\packages\arduino\tools\avrdude\6.3.0-arduino9/etc/avrdude.conf"

Using Port : COM4
Using Programmer : arduino
Overriding Baud Rate : 115200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack

eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: reading input file "C:\DOCUME~1\Owner\LOCALS~1\Temp\arduino_build_280955/Blink.ino.hex"
avrdude: writing flash (928 bytes):

Writing | ################################################## | 100% 0.38s

avrdude: 928 bytes of flash written
avrdude: verifying flash memory against C:\DOCUME~1\Owner\LOCALS~1\Temp\arduino_build_280955/Blink.ino.hex:
avrdude: load data flash data from input file C:\DOCUME~1\Owner\LOCALS~1\Temp\arduino_build_280955/Blink.ino.hex:
avrdude: input file C:\DOCUME~1\Owner\LOCALS~1\Temp\arduino_build_280955/Blink.ino.hex contains 928 bytes
avrdude: reading on-chip flash data:

| ################################################## | 100% 0.34s
Reading
avrdude: verifying ...
avrdude: 928 bytes of flash verified

avrdude done. Thank you.

2

Does not look like it failed. Do I miss something ?

3

The breadboard hasva led attached to D13 it does not flash, also the ftdi programmer shows no activity and i get thecavrdude getsync error.

4

Mben1229:
The breadboard hasva led attached to D13

Are you certain it's connected to Arduino pin 13? That is different from physical pin number 13 (which is different depending on which package the IC is in). Arduino pin 13 is PB5.

Mben1229:
i get thecavrdude getsync error.

You sure didn't in the output you posted. The output you posted shows a successful upload.

5

Thank you for your response,the led is connected to physical pin 19, Arduino D13, if the upload was successful as you stated, why wouldnt the ftdi show activity while the code is uploading and the led not blink, im totally puzzled, I have used the ftdi programmer on many occassions and it always shows rx\ tx activity when uploading.

6

Is the lack of FTDI activity only on the uploads where you get the getsync error?

7

Thank You to who all who replied, the problem was choosing the wrong breadboard, I have 2 duplicates 1 with a bad or loose solder connection and its the 1 with the sync error the verbose output was from the 2 nd board that I hadnt put the led in place and wasnt paying attention to the ftdi when it was programmed, in short both atemega328p ic will accept the sketch ad blink the led, thanks for the response Shannon.

8

I'm glad to hear you solved the problem. Enjoy!
Per