Brownout detector was triggered

Projects Programming
4

I used the sketch example available on Arduino IDE, and the output can be seen in the image I uploaded. I am only using power from the laptop. Since my last purchase, I have been using this ESP 32 for my projects involving several sensors and modules, such as the DHT 22 sensor (connected to GPIO pin 4 and 5V power source), MLX sensor, and I2C LCD (connected to GPIO pins 23, 22, 3.3V for MLX, and 5V for LCD), the SCT-013 sensor module (connected to GPIO pin 33 with a 3.3V power source), and an AC dimmer (ZC pin connected to GPIO 12 and DIM to GPIO 13, 3.3V), with all grounds connected to the same pin. There is indeed a port change, but when I performed the scan, I used a USB 3.2 Gen 2 port with power-off USB charging, adhering to the 5V voltage standard. I also used the Arduino IDE, and I conducted testing both when the ESP was not connected to the components and when the ESP 32 was connected to the components mentioned above.
This is an example of a wifi.scan sketch.

/*
 *  This sketch demonstrates how to scan WiFi networks.
 *  The API is based on the Arduino WiFi Shield library, but has significant changes as newer WiFi functions are supported.
 *  E.g. the return value of `encryptionType()` different because more modern encryption is supported.
 */
#include "WiFi.h"

void setup()
{
    Serial.begin(115200);

    // Set WiFi to station mode and disconnect from an AP if it was previously connected.
    WiFi.mode(WIFI_STA);
    WiFi.disconnect();
    delay(100);

    Serial.println("Setup done");
}

void loop()
{
    Serial.println("Scan start");

    // WiFi.scanNetworks will return the number of networks found.
    int n = WiFi.scanNetworks();
    Serial.println("Scan done");
    if (n == 0) {
        Serial.println("no networks found");
    } else {
        Serial.print(n);
        Serial.println(" networks found");
        Serial.println("Nr | SSID                             | RSSI | CH | Encryption");
        for (int i = 0; i < n; ++i) {
            // Print SSID and RSSI for each network found
            Serial.printf("%2d",i + 1);
            Serial.print(" | ");
            Serial.printf("%-32.32s", WiFi.SSID(i).c_str());
            Serial.print(" | ");
            Serial.printf("%4d", WiFi.RSSI(i));
            Serial.print(" | ");
            Serial.printf("%2d", WiFi.channel(i));
            Serial.print(" | ");
            switch (WiFi.encryptionType(i))
            {
            case WIFI_AUTH_OPEN:
                Serial.print("open");
                break;
            case WIFI_AUTH_WEP:
                Serial.print("WEP");
                break;
            case WIFI_AUTH_WPA_PSK:
                Serial.print("WPA");
                break;
            case WIFI_AUTH_WPA2_PSK:
                Serial.print("WPA2");
                break;
            case WIFI_AUTH_WPA_WPA2_PSK:
                Serial.print("WPA+WPA2");
                break;
            case WIFI_AUTH_WPA2_ENTERPRISE:
                Serial.print("WPA2-EAP");
                break;
            case WIFI_AUTH_WPA3_PSK:
                Serial.print("WPA3");
                break;
            case WIFI_AUTH_WPA2_WPA3_PSK:
                Serial.print("WPA2+WPA3");
                break;
            case WIFI_AUTH_WAPI_PSK:
                Serial.print("WAPI");
                break;
            default:
                Serial.print("unknown");
            }
            Serial.println();
            delay(10);
        }
    }
    Serial.println("");

    // Delete the scan result to free memory for code below.
    WiFi.scanDelete();

    // Wait a bit before scanning again.
    delay(5000);
}

brownout
brownout793×247 5.74 KB