Custom PCB - Error Uploading Sketch (Error, Schematic and Project Pic Attached)

Development Tools Uploading
1

Hello,

I had a handful of custom PCBs built for a stepper motor project that I am working on. It's an ATmega328P-AU TQFP (Arduino bootloader installed) with and L293dd driver on-board. I'm using Arduino as ISP to program. I have a test nano (ICSP pins) that I can successfully upload a sketch to via the UNO. I am unable to upload a sketch to my prototype board. I do have a 10k resistor on the reset pin going to +. I'm wondering if I need a capacitor as well on the reset pin. Looks like a wiring issue judging by the 0's in the error? I've been tinkering with this thing for a while and can't seem to figure it out. Any help is greatly appreciated. Please see the error message and schematic below:

Using Port : COM4
Using Programmer : arduino
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack

eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : Arduino
Description : Arduino
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.00s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

avrdude done. Thank you.

An error occurred while uploading the sketch

funproject.JPG
funproject.JPG997×1092 174 KB

funproject2.JPG
funproject2.JPG2163×978 122 KB

2

Either wiring mistake (check pinout - do you have it mirrored by any chance, ie, you have header installed on the opposite side of the board as the pinout would be correct for? Connector rotated the wrong way?), or the crystal isn't oscillating (correct value of loading caps? Check that none of the xtal pins are shorted to ground - really easy to get solder bridge under the cap when hand assembling SMD parts). Also check for bad solder joints on crystal and isp pins, especially if hand assembling, and for solder bridges between said pins.