DC gear Motor with L298N Driver millis function is not working properly

Here is a code-version that uses two very useful macros for serial-debug-output
This version makes visible what your code does

// start of macros dbg and dbgi
#define dbg(myFixedText, variableName) \
  Serial.print( F(#myFixedText " "  #variableName"=") ); \
  Serial.println(variableName);
// usage: dbg("1:my fixed text",myVariable);
// myVariable can be any variable or expression that is defined in scope

#define dbgi(myFixedText, variableName,timeInterval) \
  do { \
    static unsigned long intervalStartTime; \
    if ( millis() - intervalStartTime >= timeInterval ){ \
      intervalStartTime = millis(); \
      Serial.print( F(#myFixedText " "  #variableName"=") ); \
      Serial.println(variableName); \
    } \
  } while (false);
// usage: dbgi("2:my fixed text",myVariable,1000);
// myVariable can be any variable or expression that is defined in scope
// third parameter is the time in milliseconds that must pass by until the next time a 
// Serial.print is executed
// end of macros dbg and dbgi


const unsigned long eventInterval1 = 10000;
//EVENT 1 Motor going Down for 10 sec
const unsigned long eventInterval2 = 20000;
//EVENT 2  Motor going up  for 10 sec
const unsigned long eventInterval3 = 30000;
//EVENT 3  Motor is off (Holding Position)  for 10 sec
const unsigned long eventInterval4 = 40000;
//EVENT 4  Motor is going up  for 10 sec


unsigned long previousTime_1 = 0;
unsigned long previousTime_2 = 0;
unsigned long previousTime_3 = 0;
unsigned long previousTime_4 = 0;
int motor2pin1 = 4;
int motor2pin2 = 5;


void setup() {
  // put your setup code here, to run once:

  Serial.begin(115200);
  Serial.println("Setup-Start");
  pinMode(motor2pin1, OUTPUT);// Motor
  pinMode(motor2pin2, OUTPUT);//Motor
  pinMode(9, OUTPUT); // Enable pin motor speed regulation
}


void loop(){
  unsigned long currentTime = millis();
  // put your main code here, to run repeatedly:
  dbgi("Top of loop currentTime - previousTime_1",(currentTime - previousTime_1)/1000,2000);
  dbgi("Top of loop currentTime - previousTime_2",(currentTime - previousTime_2)/1000,2000);
  dbgi("Top of loop currentTime - previousTime_3",(currentTime - previousTime_3)/1000,2000);
  dbgi("Top of loop currentTime - previousTime_4",(currentTime - previousTime_4)/1000,2000);
  analogWrite(9, 240); //speed regulation
  
  if (currentTime - previousTime_1 >= eventInterval1) { //EVENT1
    //Motor is going up witth sensor
    digitalWrite(motor2pin1, HIGH);
    digitalWrite(motor2pin2, LOW);
    dbg("TRUE eventInterval1, HIGH/LOW",1);
    previousTime_1 = currentTime;
  }

  if (currentTime - previousTime_2 >= eventInterval2) {
    digitalWrite(motor2pin1, LOW);
    digitalWrite(motor2pin2, HIGH);
    dbg("TRUE eventInterval2, LOW/HIGH",2);
    previousTime_2 = currentTime;
  }

  if (currentTime - previousTime_3 >= eventInterval3) {
    digitalWrite(motor2pin1, LOW);
    digitalWrite(motor2pin2, LOW);
    dbg("TRUE eventInterval3, LOW/LOW",3);
    previousTime_3 = currentTime;
  }

  if (currentTime - previousTime_4 >= eventInterval4) {
    digitalWrite(motor2pin1, LOW);
    digitalWrite(motor2pin2, HIGH);
    dbg("TRUE eventInterval4, LOW/HIGH",4);
    previousTime_4 = currentTime;
  }
}

I guess that you want the things to happen in sequence

const unsigned long eventInterval1 = 10000;
//EVENT 1 Motor going Down for 10 sec
const unsigned long eventInterval2 = 20000;
//EVENT 2  Motor going up  for 10 sec
const unsigned long eventInterval3 = 30000;
//EVENT 3  Motor is off (Holding Position)  for 10 sec
const unsigned long eventInterval4 = 40000;
//EVENT 4  Motor is going up  for 10 sec

This can be programmed with a software-functionality called state-machine.
State-machines reduce the number of if-conditions you have to check.

If you want to happen the things in sequence
then every 10 seconds the state-machine is switched to the next state

best regards Stefan