# Differences between Giga boards/Shields?

**URL:** <https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364>\
**Category:** GIGA Display Shield\
**Created:** [June 12, 2025, 12:59am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364 "2025-06-12T00:59:30Z")\
**Posts on this page:** 13\
**Page:** 1

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [June 12, 2025, 12:59am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/1 "2025-06-12T00:59:31Z")

</div>

Sorry maybe sort of a random question, but I have two GIGA boards and both of them I currently have a GIGA shield on them.

Currently I am mostly using them to experiment with Zephyr and I have noticed differences on how these two boards behave. I bought both boards Several months (year?) apart.

For example on Zephyr: One of the boards, when I upload anything to them, like flashing new logical firmware or download a sketch, I always have to go to the kernel monitor, and type in: sketch  
to make it run. The other board, I typically do not have to do this. Only if there was a problem loading it, like missing symbol, do I have to maybe type in sketch to find out what the problem. This has been going on for several months.

The touch coordinates are different between these two setups.  
On the first board I mentioned, if you are looking at the screen in landscape mode with the camera on top, if I touch near the corners I see coordinates like:  
UL: 456, 26 LL:4, 23 UR: 434, 782, LR: 23, 774.

With the other setup:  
UL: 17, 14 LL:23, 434 UR: 782, 19 LR 788, 464

It is like the sensor is rotated or the the like.  
Note; This was done with the example sketch: Touch\_polling running on the MBED version of Arduino GIGA... I have seen the same results using my updated version of the Arduino\_GigaDisplayTouch library running on Zephyr.

Wondering if these differences are due to changes to the boards? If so are there programmatic ways to detect which version we have?

Thanks

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 10, 2026, 1:04am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/2 "2026-09-10T01:04:31Z")

</div>

@ptillisch and all,

I am still having the same same issue between the two Different Display shields.

It has been awhile since I did much touch, and since I had both boards running at the  
same time in the same sketch...

It feels like someone attached the touch sensor rotated 90 degrees.  
Is there a way to detect this in hardware and or setting to compensate within driver?  
Or do sketches need to tranlate the coordinates them self?

Like on this one, sort of rough positions 480 is probably 479...

 ![image](https://europe1.discourse-cdn.com/arduino/original/4X/9/1/2/912af1f6094b9faf80f925bda4a619ef39fa0977.jpeg)

The other top left is like 0.0...  
Which one is Right?

---

<div class="post-metadata">

**Author:** ![steve9](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/steve9/32/1098630_2.png) [@steve9](https://forum.arduino.cc/u/steve9)\
**Post date:** [September 10, 2026, 6:26am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/3 "2026-09-10T06:26:08Z")

</div>

Hi @KurtE

> [@KurtE](#):
>
> are there programmatic ways to detect which version we have?

Not tried it (don't have the display), but querying these registers of the GT911 might reveal differences:

 ![Screenshot 2026-09-10 071319](https://europe1.discourse-cdn.com/arduino/original/4X/3/5/4/354f2a9ec8097c753280c0de7346131e52d91028.jpeg)

> [@KurtE](#):
>
> It feels like someone attached the touch sensor rotated 90 degrees.  
> Is there a way to detect this in hardware and or setting to compensate within driver?

There's a raft of other registers that you could query that could assist

> **[Configuration Information (R/W) - Goodix GT911 Programming Manual \[Page 5\]](https://www.manualslib.com/manual/2874744/Goodix-Gt911.html?page=5#manual)**
>
> Do you have a question about the GT911 and is the answer not in the manual? | Goodix GT911 Manual Online: Configuration Information (R/W). Register Config Data Config\_ 0x8047 Version X Output Max 0x8048 (Low Byte) X Output Max 0x8049 (High Byte) Y...

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 10, 2026, 2:54pm UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/4 "2026-09-10T14:54:28Z")

</div>

> [@steve9](#):
>
> Not tried it (don't have the display), but querying these registers of the GT911 might reveal differences:

Thanks,

I downloaded the manual from:

[https://www.bing.com/ck/a?!&&p=31fab780c8a2b3c58dd4d6eb183f13ced2d210613c8d01eac7f7b8085c72b76bJmltdHM9MTc4ODk5ODQwMA&ptn=3&ver=2&hsh=4&fclid=1f32e013-e10a-6992-301b-f552e0276895&psq=goodix+gt911+manual&u=a1aHR0cHM6Ly93d3cuY3J5c3RhbGZvbnR6LmNvbS9jb250cm9sbGVycy9HT09ESVgvR1Q5MTFQcm9ncmFtbWluZ0d1aWRlLzQ3OC8](https://www.bing.com/ck/a?!&&p=31fab780c8a2b3c58dd4d6eb183f13ced2d210613c8d01eac7f7b8085c72b76bJmltdHM9MTc4ODk5ODQwMA&ptn=3&ver=2&hsh=4&fclid=1f32e013-e10a-6992-301b-f552e0276895&psq=goodix+gt911+manual&u=a1aHR0cHM6Ly93d3cuY3J5c3RhbGZvbnR6LmNvbS9jb250cm9sbGVycy9HT09ESVgvR1Q5MTFQcm9ncmFtbWluZ0d1aWRlLzQ3OC8)

I have hacked up a simple Zephyr sketch I have for doing touch paint on the  
display...  
[zephyr\_GIGA\_shield\_touchpaint-260910a.zip](https://forum.arduino.cc/uploads/short-url/4xj7AaSWVmyHKCsFluvFifBBdbs.zip) (3.0 KB)

Note: It uses my MemoryHexDump to do the printing...  
[KurtE/MemoryHexDump: Simple Arduino Memory Dump](https://github.com/kurte/memoryhexdump)

This is from the Display that works currently with the touch paint.

```arduino
Touch Paint!
Touch controller init - OK
Touch Orientation: 0
Can change by typing 0-3 in Serial monitor
GFX Rotation: 0
--------------------------------------------------------
GT911 Registers
00008047 - 41 20 03 E0 01 05 4D 00 01 08 28 05 50 32 03 10 : A ....M. ..(.P2..
00008057 - 00 00 00 00 00 00 00 00 00 00 00 86 26 07 17 15 : ........ ....&...
00008067 - 31 0D 00 00 01 9B 03 1D 00 00 00 00 00 03 64 32 : 1....... ......d2
00008077 - 00 00 00 0F 4B 94 C5 02 07 00 00 04 9C 11 00 72 : ....K... .......r
00008087 - 18 00 55 21 00 41 2E 00 32 40 00 32 00 00 00 00 : ..U!.A.. 2@.2....
00008097 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
000080A7 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
000080B7 - 12 10 0E 0C 0A 08 06 FF FF FF FF FF FF FF 00 00 : ........ ........
000080C7 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 22 21 : ........ ......"!
000080D7 - 20 1F 1E 1D 00 02 04 06 08 0A FF FF FF FF FF FF : ....... ........
000080E7 - FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 : ........ ........
000080F7 - 00 00 00 00 00 00 00 00 92 : ........ .
GT911 Registers
00008140 - 39 31 31 00 60 10 20 03 E0 01 00 00 00 00 00 00 : 911.`. . ........
00008150 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
00008160 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
00008170 - 00 00 00 00 00 00 : ......
--------------------------------------------------------

```

And this is from the other where the coordinates are different:

```arduino
GFX Rotation: 0
--------------------------------------------------------
GT911 Registers
00008047 - 41 E0 01 20 03 05 05 00 01 08 28 05 50 32 03 05 : A.. .... ..(.P2..
00008057 - 00 00 00 00 00 00 00 00 00 00 00 86 26 07 17 15 : ........ ....&...
00008067 - 31 0D 00 00 01 9B 03 1D 00 00 00 00 00 03 64 32 : 1....... ......d2
00008077 - 00 00 00 0F 4B 94 C5 02 07 00 00 04 9C 11 00 72 : ....K... .......r
00008087 - 18 00 55 21 00 41 2E 00 32 40 00 32 00 00 00 00 : ..U!.A.. 2@.2....
00008097 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
000080A7 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
000080B7 - 12 10 0E 0C 0A 08 06 FF FF FF FF FF FF FF 00 00 : ........ ........
000080C7 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 22 21 : ........ ......"!
000080D7 - 20 1F 1E 1D 00 02 04 06 08 0A FF FF FF FF FF FF : ....... ........
000080E7 - FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 : ........ ........
000080F7 - 00 00 00 00 00 00 00 00 E5 : ........ .
GT911 Registers
00008140 - 39 31 31 00 60 10 E0 01 20 03 00 00 00 00 00 00 : 911.`... .......
00008150 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
00008160 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
00008170 - 00 00 00 00 00 00 : ......
--------------------------------------------------------

```

There are obviously differences:  
Like Just looking at the first several registers:  
8047 Config version - both 41  
**8048-49 X Output MAX: 800 versus 480**  
**804A-4B Y Output Max: 480 versus 800**  
804C - Both support up to 5 touch points  
804D - Module Switch 1: 0x4D versus 0x05  
Bit6：Sensor\_Resersal(X2X), configured as 1 indicates X axis reversal.  
...

Question is Why? And is this a one off issue, or ...  
And Best way to resolve? For my own sketch I can probably add  
code to read one or more of these registers as I did here, detect that things  
are reversed...

But I wonder if Arduino is aware of these differences and potentially have a patch  
program to update one or the other?

@ptillisch @pennam and all - Suggestions? Or should I create an issue maybe to the library:  
[arduino-libraries/Arduino\_GigaDisplayTouch](https://github.com/arduino-libraries/Arduino_GigaDisplayTouch) ?

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 10, 2026, 3:16pm UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/5 "2026-09-10T15:16:41Z")

</div>

> [@KurtE](#):
>
> Or should I create an issue maybe to the library:  
> [arduino-libraries/Arduino\_GigaDisplayTouch](https://github.com/arduino-libraries/Arduino_GigaDisplayTouch) ?

I went ahead and created an issue:

[Does not Work with all Arduino GIGA Displays, differences with GT911 configuration. · Issue #23 · arduino-libraries/Arduino\_GigaDisplayTouch](https://github.com/arduino-libraries/Arduino_GigaDisplayTouch/issues/23)

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 10, 2026, 10:30pm UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/6 "2026-09-10T22:30:36Z")

</div>

As a current test/work around, I have a hacked up version of the Touchpaint  
[zephyr\_GIGA\_shield\_touchpaint-260910a.zip](https://forum.arduino.cc/uploads/short-url/ayjJ29brNqw1tX0ogoVBDbzFqsu.zip) (3.3 KB)

Where I use:

```arduino
// lets see if we think the GT911 if off.
  uint8_t switch_1;
  ReadGT911Registers(GT911_REG_CONFIG_MODULE_SWITCH1, &switch_1, 1);
  g_touch_Alt_config = (switch_1 & 0x40) ? false : true;
  if (switch_1 & 0x40) Serial.println("GT911 Normal display(Sensor_Resersal(X2X))");
  else Serial.println("GT911 display sensor different");

```

Then I use a helper function to convert the raw inputs depending on Old versus New

```arduino
void convertRawTouchyByRotation(int xRaw, int yRaw, int &touch_x, int &touch_y) {
  if (g_touch_Alt_config) {
    switch (g_touch_rotation) {
      case 0:
        touch_x = xRaw;
        touch_y = yRaw;
        break;
      case 1:
        touch_x = yRaw; //display.width() - xRaw;
        touch_y = display.height() - xRaw; // display.height() - yRaw;
        break;
      case 2:
        touch_x = display.width() - xRaw;
        touch_y = display.height() - yRaw;
        break;
      case 3:
        touch_x = display.width() - yRaw;
        touch_y = xRaw;
        break;
    }

  } else {
    switch (g_touch_rotation) {
      case 0:
        touch_y = xRaw;
        touch_x = display.width() - yRaw;
        break;
      case 1:
        touch_x = xRaw; //display.width() - xRaw;
        touch_y = yRaw; // display.height() - yRaw;
        break;
      case 2:
        touch_x = yRaw;
        touch_y = display.height() - xRaw;
        break;
      case 3:
        touch_x = display.width() - xRaw;
        touch_y = display.height() - yRaw;
        break;
    }
  }
}

```

The sketch now allows me to type in a new rotation 0-3, at which time  
it will set the screen rotation and draw the color pallet and then map the touch.

This appears to be working on both of my two displays.

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 11, 2026, 10:59pm UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/7 "2026-09-11T22:59:59Z")

</div>

@ptillisch @pennam @facchinm and all - It would be great to know if for example my newer display was a one off oops or if Arduino changed the configuration of the registers at some point.

Note: Our (@Merlin513 and mine) Displays we purchased early on, have what I say is  
the main/ not alternate configuration.

What is interesting about this configuration, is when the screen is in landscape mode (orientation 1), the Touch is setup to the X and Y match the screen X, Y:

```arduino
      case 1:
        touch_x = yRaw; //display.width() - xRaw;
        touch_y = display.height() - xRaw; // display.height() - yRaw;
        break;

```

Where as the one I purchased later on, has what I currently call the Alternate or different configuration. The interesting thing here is, if you are in default rotation (0), or portrait mode the positions returned from the GT911 match the screen coordinates.

```arduino
      case 0:
        touch_x = xRaw;
        touch_y = yRaw;
        break;

```

It would be great if a few people with older and newer displays would try running this  
sketch on ArduinoCore-zephyr and see which configuration it has. And  
with latest version of sketch if you type 0-3 in Serial monitor it will change the screen to that  
orientation, and if you can touch the screen and the touchpaint appears to be tracking  
correctly that would be great to know.

Thanks

---

<div class="post-metadata">

**Author:** ![ptillisch](https://avatars.discourse-cdn.com/v4/letter/p/ad7895/32.png) [@ptillisch](https://forum.arduino.cc/u/ptillisch)\
**Post date:** [September 12, 2026, 12:23am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/8 "2026-09-12T00:23:50Z")

</div>

> [@KurtE](#):
>
> It would be great if a few people with older and newer displays would try running this  
> sketch on ArduinoCore-zephyr and see which configuration it has. And  
> with latest version of sketch if you type 0-3 in Serial monitor it will change the screen to that  
> orientation, and if you can touch the screen and the touchpaint appears to be tracking  
> correctly that would be great to know.

The detected touch coordinates work correctly with the sketch, with all four orientations.

I'm pretty sure I bought my GIGA Display Shield soon after it was released. It says "V0.5" on the copper layer on the connector side of the PCB.

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 12, 2026, 12:47am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/9 "2026-09-12T00:47:35Z")

</div>

Thanks,

Curious did it print  
GT911 Normal display(Sensor\_Resersal(X2X)  
Or  
GT911 display sensor different

---

<div class="post-metadata">

**Author:** ![ptillisch](https://avatars.discourse-cdn.com/v4/letter/p/ad7895/32.png) [@ptillisch](https://forum.arduino.cc/u/ptillisch)\
**Post date:** [September 12, 2026, 12:49am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/10 "2026-09-12T00:49:30Z")

</div>

Here is the output from the sketch:

```plaintext
Touch Paint!
Touch controller init - OK
Touch Orientation: 0
Can change by typing 0-3 in Serial monitor
GFX Rotation: 0
--------------------------------------------------------
GT911 Registers
00008047 - 41 E0 01 20 03 05 05 00 01 08 28 05 50 32 03 05 : A.. .... ..(.P2..
00008057 - 00 00 00 00 00 00 00 00 00 00 00 86 26 07 17 15 : ........ ....&...
00008067 - 31 0D 00 00 01 9B 03 1D 00 00 00 00 00 03 64 32 : 1....... ......d2
00008077 - 00 00 00 0F 4B 94 C5 02 07 00 00 04 9C 11 00 72 : ....K... .......r
00008087 - 18 00 55 21 00 41 2E 00 32 40 00 32 00 00 00 00 : ..U!.A.. 2@.2....
00008097 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
000080A7 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
000080B7 - 12 10 0E 0C 0A 08 06 FF FF FF FF FF FF FF 00 00 : ........ ........
000080C7 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 22 21 : ........ ......"!
000080D7 - 20 1F 1E 1D 00 02 04 06 08 0A FF FF FF FF FF FF : ....... ........
000080E7 - FF FF FF FF FF FF FF FF 00 00 00 00 00 00 00 00 : ........ ........
000080F7 - 00 00 00 00 00 00 00 00 E5 : ........ .
GT911 Registers
00008140 - 39 31 31 00 60 10 E0 01 20 03 00 00 00 00 00 00 : 911.`... .......
00008150 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
00008160 - 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 : ........ ........
00008170 - 00 00 00 00 00 00 : ......
--------------------------------------------------------
GT911 display senseor different

```

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 12, 2026, 1:37am UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/11 "2026-09-12T01:37:16Z")

</div>

Thanks,

That matches my I believe newer one.  
Both of mine show the 0.5...

I know that @Merlin513 one matches my older one as well.

Sorry I know we are spending a lot of time on some of this, but finding that playing with things like this help find and maybe hopefully resolve issues.  
[giga\_weather\_display\_v5-260911a.zip](https://forum.arduino.cc/uploads/short-url/jV5wmtaYk5tBqpzObJSkwulRup0.zip) (121.9 KB)

Here is my current version of the Weather sketch...  
Main screen:

 ![image](https://europe1.discourse-cdn.com/arduino/original/4X/5/8/2/5823b78eab54f368022efd24b8a3f4cc5e079a75.jpeg)

If you touch one of the days it will drill into that day  
Click back to go back to main screen.

 ![image](https://europe1.discourse-cdn.com/arduino/original/4X/d/4/b/d4bb30c7eb5e80a646881ef47239ceddf63bbe42.jpeg)

Click on symbol toward upper right for Keyboard:  
Brings up:

 ![image](https://europe1.discourse-cdn.com/arduino/original/4X/8/f/6/8f6c5baaaca7ba038b69b740b14424eed16cf878.png)

Where you can click on buttons to type in new loactions.

Things so far with this sketch:  
a) WiFi - One of my boards is much better at connecting...  
b) I am using /storage/ file to save security data as well as Location information. - Issues with partitions, some bad block? Maybe difference between old or new board?  
c) Touch Orientation.  
d) Maybe Touch timing differences?  
...

But at least we are having some fun!

Thanks again

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 12, 2026, 1:21pm UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/12 "2026-09-12T13:21:08Z")

</div>

Thought I would mention found another good document/website to look at:

[Programming a Capacitive Touch Panel utilizing the GT911 Touch Controller - Focus LCDs](https://focuslcds.com/application-notes/programming-a-capacitive-touch-panel-utilizing-the-gt911-touch-controller/)

---

<div class="post-metadata">

**Author:** ![KurtE](https://dub1.discourse-cdn.com/arduino/user_avatar/forum.arduino.cc/kurte/32/1246572_2.png) [@KurtE](https://forum.arduino.cc/u/KurtE)\
**Post date:** [September 12, 2026, 3:51pm UTC](https://forum.arduino.cc/t/differences-between-giga-boards-shields/1388364/13 "2026-09-12T15:51:33Z")

</div>

> [@KurtE](#):
>
> c) Touch Orientation.  
> d) Maybe Touch timing differences?

I thought would mention, that have found issues with differences between the two register configurations of the different Displays.

Orientation as I mentioned above..

Timing: does work differently in mentioned sketch. Needed to adjust a delay depending on configuration: I noticed in the Above dumps: The register:  
8056: was different: Our original one 0x10, the Other config 0x5  
From the GT911 programming guide it shows:  
 ![image](https://europe1.discourse-cdn.com/arduino/original/4X/d/b/a/dbad600915c938f513035805555f4584a93b33f4.png)

Which is different than register number from the Focus LCDs documents?

But as for talking about the Weather app will continue on the thread:  
[Playing with Zephyr V1.0.0 on GIGA and Wifi - Mega / GIGA R1 WiFi - Arduino Forum](https://forum.arduino.cc/t/playing-with-zephyr-v1-0-0-on-giga-and-wifi/1458103)
