Due pinout diagram

quite readable now on my color laser printer. thanks for lightening up the blue. in fact, it looks just like the version i modified in photoshop.

Good, note the errata on the first post as well. I haven't got the energy/time to regenerate the files right now :)


Rob

1) This recent activity has made a good document gooder.

2) Your endeavour in time and effort to produce the 'Unofficial Guide' seems out of whack with comments.

3) Noah did, and nr Bundaberg may have somewhat, shared similar water issues.

1) Thanks, but shouldn't that be "more better"?

2) I've currently got the shits with Arduino Inc but I'll get over it. :) Meanwhile I created this document so it behooves me to make it as good as possible.

3) We're up in the hills, apart from the fact that the grass is 5-foot high and it rains every day so we can't cut it the recent events have not affected us thankfully. We just got home in time, Gympie is isolated again today with the highway cut on both sides, we drove through there a couple of days ago. This is Gympie's 4th flood in a year. Poor buggers.


Rob

Regarding the two LEDs, I’ve seen several posts of people getting confused about which LEDs they are looking at. So if at all just for identification and clarification so they don’t get confused of what they are, as opposed to the ones used for programming.

OK you talked me into it :), see the first post and advise if the text is not clear/correct.


Rob

It looks like the physical pin color was shifted from dark gray to light blue. The LED and SPI physical pin bubbles remain dark gray (no pun intended).

Bugger, I'll fix shortly.


Rob

All errata (as far as I know) fixed, new versions uploaded.


Rob

Nobody seemed to have asked these questions before, so I'll ask it now: 1. Why do all pins have a "Digital Pin" and "Physical Pin" and "Port Pin" alias? Where are these aliases used to refer to these pins - for instance, when would I need to refer to pin A3 by A.22, or AD4, or D57, or 81? 2. There seem to be many Reset pins. What does the Reset pin in the SPI cluster reset?

Digital pin is the Arduino name and that’s what most people would use.

Port pin is for those who are working directly with ports and not the Arduino abstraction layer.

Physical pin is for those who need to actual probe the chip and therefore have to know the real pin.

I don’t think there’s any programming syntax that uses say “A.22” as such, that’s just a common way to indicate bit 22 of port A.
Likewise for ADn, but if you are working directly with the ADC hardware you need to know what actual input is being addressed and “AD4” is as good a way as any to do that and the terminology used by Atmel.

Use A3 (for example) for analogRead().

Just the number for digitalRead/Write, ie 57 not D57.

AFAIK all the reset pins go to the same place, it’s just that the various connectors use the signal at different times.


Rob

Thanks for this - It is really helpful!

Excellent post :). Thanks for this. Very helpfull!

Glad to help.


Rob

where did you get the info on the high current vs low current pins? I’d like to map out some other pins from a design i’m working on but i can’t figure out whether they are the high current or low current pins. :frowning:

See page 1391: http://www.atmel.com/Images/doc11057.pdf

thanks!! :D

GreyNomad,

You said: "I have also completely lost interest in the Due for a couple of reasons."

Why? Isn´t it a very good board?

Hmmm, did I say that did I :)

There's nothing wrong with the Due, it's just that IMO it could have been a lot better. They ignored most of the neat hardware the chip has, mostly I assume in favour of Mega shield compatibility, so we have a powerful ARM board that can flash 54 LEDs but cannot interface correctly to an SD card, external memory or Ethernet.

I think it could have kept Duemilanove/Uno shield compatibility and used the spare pins for more useful functions. But then I would think that because it's exactly what I've done with my latest Mega2560 design and plan to do with a SAM design soon :)


Rob

Just wanted to thank you for putting out this diagram. It has helped a lot.

But I would like to have one addition to this diagram. The addition of quadrature inputs would be a great help.

Also, if you can make a second diagram that listed the primary pin designations and has a empty box so that the user can designate what pens are used for what purpose in their project, it would be very helpful.

Again, thank you, it has been a great help.

Joe.