IDE 2.3.6 ESP-Core 3.2.1
Mit diesen Einstellungen bekomme ich eine ausführliche Ausgabe zum Speicher, wenn ich den seriellen Monitor auf den zweiten USB-Anschluß, bei mir USB10, umstelle:
Klapp mich auf
=========== Before Setup Start ===========
Chip Info:
------------------------------------------
Model : ESP32-S3
Package : 0
Revision : 0.02
Cores : 2
CPU Frequency : 240 MHz
XTAL Frequency : 40 MHz
Features Bitfield : 0x00000012
Embedded Flash : No
Embedded PSRAM : No
2.4GHz WiFi : Yes
Classic BT : No
BT Low Energy : Yes
IEEE 802.15.4 : No
------------------------------------------
INTERNAL Memory Info:
------------------------------------------
Total Size : 376728 B ( 367.9 KB)
Free Bytes : 335668 B ( 327.8 KB)
Allocated Bytes : 35900 B ( 35.1 KB)
Minimum Free Bytes: 330820 B ( 323.1 KB)
Largest Free Block: 262132 B ( 256.0 KB)
------------------------------------------
SPIRAM Memory Info:
------------------------------------------
Total Size : 8388608 B (8192.0 KB)
Free Bytes : 8386088 B (8189.5 KB)
Allocated Bytes : 144 B ( 0.1 KB)
Minimum Free Bytes: 8386088 B (8189.5 KB)
Largest Free Block: 8257524 B (8064.0 KB)
Bus Mode : OPI
------------------------------------------
Flash Info:
------------------------------------------
Chip Size : 16777216 B (16 MB)
Block Size : 65536 B ( 64.0 KB)
Sector Size : 4096 B ( 4.0 KB)
Page Size : 256 B ( 0.2 KB)
Bus Speed : 80 MHz
Bus Mode : QIO
------------------------------------------
Partitions Info:
------------------------------------------
nvs : addr: 0x00009000, size: 20.0 KB, type: DATA, subtype: NVS
otadata : addr: 0x0000E000, size: 8.0 KB, type: DATA, subtype: OTA
app0 : addr: 0x00010000, size: 8128.0 KB, type: APP, subtype: OTA_0
app1 : addr: 0x00800000, size: 8128.0 KB, type: APP, subtype: OTA_1
coredump : addr: 0x00FF0000, size: 64.0 KB, type: DATA, subtype: COREDUMP
------------------------------------------
Software Info:
------------------------------------------
Compile Date/Time : Aug 17 2025 12:10:52
Compile Host OS : windows
ESP-IDF Version : v5.4.2-25-g858a988d6e
Arduino Version : 3.2.1
------------------------------------------
Board Info:
------------------------------------------
Arduino Board : ESP32_S3R8N16
Arduino Variant : esp32_s3r8n16
Arduino FQBN : esp32:esp32:gen4-ESP32-S3R8n16:UploadSpeed=921600,USBMode=hwcdc,CDCOnBoot=cdc,MSCOnBoot=default,DFUOnBoot=default,UploadMode=default,CPUFreq=240,FlashMode=qio,FlashSize=16M,PartitionScheme=gen4esp32scheme3,DebugLevel=verbose,PSRAM=opi,LoopCore=1,EventsCore=1,EraseFlash=all
============ Before Setup End ============
Start
[ 1965][V][esp32-hal-periman.c:235] perimanSetBusDeinit(): Deinit function for type GPIO (1) successfully set to 0x4202a89c
[ 1967][V][esp32-hal-periman.c:160] perimanSetPinBus(): Pin 21 successfully set to type GPIO (1) with bus 0x16
=========== After Setup Start ============
INTERNAL Memory Info:
------------------------------------------
Total Size : 376728 B ( 367.9 KB)
Free Bytes : 335580 B ( 327.7 KB)
Allocated Bytes : 35956 B ( 35.1 KB)
Minimum Free Bytes: 330820 B ( 323.1 KB)
Largest Free Block: 262132 B ( 256.0 KB)
------------------------------------------
SPIRAM Memory Info:
------------------------------------------
Total Size : 8388608 B (8192.0 KB)
Free Bytes : 8386088 B (8189.5 KB)
Allocated Bytes : 144 B ( 0.1 KB)
Minimum Free Bytes: 8386088 B (8189.5 KB)
Largest Free Block: 8257524 B (8064.0 KB)
------------------------------------------
GPIO Info:
------------------------------------------
GPIO : BUS_TYPE[bus/unit][chan]
--------------------------------------
21 : GPIO
43 : UART_TX[0]
44 : UART_RX[0]
============ After Setup End =============
Ich verwende des Blinkprogramm mit einer LED an GPIO21.
@HotSystems: Mit diesen Infos kann man eine eigene Konfiguration überprüfen 