Having problems making a standalone arduino

Projects Programming

xzarida October 9, 2019, 1:07am 1

Can someone tell me what I am doing wrong ?

I am trying to program a board I made on easyeda. I am trying to put a bootloader on an atmega328p and program.

I have my easyeda board i made hooked up to my arduino uno. Sck to d13 on uno miso to d12 on uno and mosi to d11 I get the error below when i try to program. I am at a complete loss. Could use some help.

[Album] imgur.com

C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.21.0_x86__mdqgnx93n4wtt\hardware\tools\avr/bin/avrdude -CC:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.21.0_x86__mdqgnx93n4wtt\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM3 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m

avrdude: Version 6.3-20171130
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.21.0_x86__mdqgnx93n4wtt\hardware\tools\avr/etc/avrdude.conf"

Using Port : COM3
Using Programmer : arduino
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack

eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : Arduino
Description : Arduino
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

avrdude done. Thank you.

Error while burning bootloader.

system October 9, 2019, 7:53am 2

(deleted)

BJHenry October 9, 2019, 12:00pm 3

xzarida:
Can someone tell me what I am doing wrong ?

The most obvious thing you're doing wrong is feeding ~6v from two CR2032s straight into the ATMega.
You're also missing the 100nF decoupling capacitors that the ATMega needs to function correctly.

xzarida October 9, 2019, 10:52pm 4

So I added a 100nf from reset pin to D10 on the uno,

I also added a 100nf cap on my power rail vcc and gnd

getting the same error

C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.21.0_x86__mdqgnx93n4wtt\hardware\tools\avr/bin/avrdude -CC:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.21.0_x86__mdqgnx93n4wtt\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM3 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDE:m -Ulfuse:w:0xFF:m

avrdude: Version 6.3-20171130
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:\Program Files\WindowsApps\ArduinoLLC.ArduinoIDE_1.8.21.0_x86__mdqgnx93n4wtt\hardware\tools\avr/etc/avrdude.conf"

Using Port : COM3
Using Programmer : arduino
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack

eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : Arduino
Description : Arduino
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000 (retrying)

Error while burning bootloader.
Reading | ################################################## | 100% 0.01s

avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.

avrdude done. Thank you.

groundFungus October 9, 2019, 11:31pm 5

You're also missing the 100nF decoupling capacitors that the ATMega needs to function correctly.

Do you have the 0.1uF decoupling caps from the Vcc pins to ground (as close to the chip as possible)?

xzarida October 9, 2019, 11:42pm 6

Yes i do

system October 10, 2019, 1:13pm 7

(deleted)

xzarida October 11, 2019, 1:41am 8

spycatcher2k:
Remove the cap to the reset!

Tell us every wire you have connected between your Arduino and this board.

SICK1 to D13
MISO1 to d12
MOSI1 to d11
Reset to D10

to 5vdc

to gnd

Thanks for the help!

I am thinking I am going to try a new board and new chip maybe some terminals shorted ? is that common for this error. It's a surface mount trip, not sure if it's even possible to use arduino as an isp

xzarida October 11, 2019, 3:31am 9

So I resoldered a new board. I have to be doing something wrong with the ISP settings, this new boards doing the same thing.

Does it matter that I have atmega328p u-th ?

I heard there might be problems with this chip

GoForSmoke October 11, 2019, 4:19am 10

This works and has chip ID software:

xzarida October 11, 2019, 1:07pm 11

GoForSmoke:
This works and has chip ID software:
Gammon Forum : Electronics : Microprocessors : How to make an Arduino-compatible minimal board

Not sure if this will work for the SMD version, but I will try to chip IDer tonight and see what happens.

xzarida October 13, 2019, 2:45pm 12

I got it to boot load! I forgot to hook up 5volt on the PCB ! Thanks for everyones help!

Topic		Replies	Views	Activity
Arduino Uno Board problems IDE 1.x	5	1420	May 5, 2021
Atmega328-PU bootloader issues IDE 1.x	4	1655	May 5, 2021
Burning/reburning bootloader to Arduino Uno/ATmega328p-au Programming	14	1495	May 6, 2021
Problem programming a standalone ATMega328 3rd Party Boards	6	1607	May 6, 2021
Problem uploading the bootloader to an arduino uno Uploading	5	543	August 17, 2023