Help changing on/off function with sensor signal to on/timed function

Projects Programming
5

Basic function to water the plant.

void fDoMoistureDetector( void * parameter )
{
  //wait for a mqtt connection
  while ( !MQTTclient.connected() )
  {
    vTaskDelay( 250 );
  }
  int      TimeToPublish = 5000000; //5000000uS
  int      TimeForADreading = 100 * 1000; // 100mS
  uint64_t TimePastPublish = esp_timer_get_time(); // used by publish
  uint64_t TimeADreading   = esp_timer_get_time();
  TickType_t xLastWakeTime = xTaskGetTickCount();
  const TickType_t xFrequency = 10; //delay for 10mS
  float    RemainingMoisture = 100.0f; //prevents pump turn on during start up
  bool     pumpOn = false;
  uint64_t PumpOnTime = esp_timer_get_time();
  int      PumpRunTime = 11000000;
  uint64_t PumpOffWait = esp_timer_get_time();
  uint64_t PumpOffWaitFor = 60000000; //one minute
  float    lowMoisture = 23.0f;
  float    highMoisture = 40.0f;
  for (;;)
  {
    //read AD values every 100mS.
    if ( (esp_timer_get_time() - TimeADreading) >= TimeForADreading )
    {
      xEventGroupSetBits( eg, evtADCreading );
      TimeADreading = esp_timer_get_time();
    }
    xQueueReceive(xQ_RM, &RemainingMoisture, 0 ); //receive queue stuff no waiting
    //read gpio 0 is water level good. Yes: OK to run pump : no pump off.   remaining moisture good, denergize water pump otherwise energize water pump.
    if ( RemainingMoisture >= highMoisture )
    {
      WaterPump0_off();
    }
    if ( !pumpOn )
    {
      log_i( "not pump on ");
      if ( gpio_get_level( GPIO_NUM_0 ) )
      {
        if ( RemainingMoisture <= lowMoisture )
        {
          //has one minute passed since last pump energize, if so then allow motor to run
          if ( (esp_timer_get_time() - PumpOffWait) >= PumpOffWaitFor )
          {
            WaterPump0_on();
            log_i( "pump on " );
            pumpOn = !pumpOn;
            PumpOnTime = esp_timer_get_time();
          }
        }
        //xSemaphoreGive( sema_RemainingMoisture );
      } else {
        log_i( "water level bad " );
        WaterPump0_off();
        PumpOffWait = esp_timer_get_time();
      }
    } else {
      /*
         pump goes on runs for X seconds then turn off, then wait PumpOffWaitTime before being allowed to energize again
      */
      if ( (esp_timer_get_time() - PumpOnTime) >= PumpRunTime )
      {
        log_i( "pump off " );
        WaterPump0_off(); // after 5 seconds turn pump off
        pumpOn = !pumpOn;
        PumpOffWait = esp_timer_get_time();
      }
    }
    // publish to MQTT every 5000000uS
    if ( (esp_timer_get_time() - TimePastPublish) >= TimeToPublish )
    {
      xQueueOverwrite( xQ_RemainingMoistureMQTT, (void *) &RemainingMoisture );// data for mqtt publish
      TimePastPublish = esp_timer_get_time(); // get next publish time
    }
    xLastWakeTime = xTaskGetTickCount();
    vTaskDelayUntil( &xLastWakeTime, xFrequency );
  }
  vTaskDelete( NULL );
}// end fDoMoistureDetector()

Hope it helps in seeing how to enable to water on at a % of moisture and turn the pump off after an X run time.

Just substitute millis() for esp_timer_get_time()

1 Like