gateway:
// Sample RFM69 receiver/gateway sketch, with ACK and optional encryption
// Passes through any wireless received messages to the serial port & responds to ACKs
// It also looks for an onboard FLASH chip, if present
// Library and code by Felix Rusu - felix@lowpowerlab.com
// Get the RFM69 and SPIFlash library at: https://github.com/LowPowerLab/
/*
NOTES:
1) RFM69 pin:
MOSI = 11
MISO = 12
SCK = 13
SS = 10
LED = ? add to code
*/
#include <RFM69.h>
#include <SPI.h>
//#include <SPIFlash.h>
#define NODEID 1 //unique for each node on same network
#define NETWORKID 100 //the same on all nodes that talk to each other
//Match frequency to the hardware version of the radio on your Moteino (uncomment one):
//#define FREQUENCY RF69_433MHZ
//#define FREQUENCY RF69_868MHZ
#define FREQUENCY RF69_915MHZ
#define ENCRYPTKEY "sampleEncryptKey" //exactly the same 16 characters/bytes on all nodes!
#define IS_RFM69HW //uncomment only for RFM69HW! Leave out if you have RFM69W!
#define ACK_TIME 30 // max # of ms to wait for an ack
//tsai: which pin is LED
#define LED 9 // Moteinos have LEDs on D9
#define SERIAL_BAUD 115200
RFM69 radio;
//SPIFlash flash(8, 0xEF30); //EF40 for 16mbit windbond chip
bool promiscuousMode = false; //set to 'true' to sniff all packets on the same network
void setup() {
Serial.begin(SERIAL_BAUD);
delay(10);
radio.initialize(FREQUENCY,NODEID,NETWORKID);
#ifdef IS_RFM69HW
radio.setHighPower(); //uncomment only for RFM69HW!
#endif
radio.encrypt(ENCRYPTKEY);
radio.promiscuous(promiscuousMode);
char buff[50];
sprintf(buff, "\nListening at %d Mhz...", FREQUENCY==RF69_433MHZ ? 433 : FREQUENCY==RF69_868MHZ ? 868 : 915);
Serial.println(buff);
/*
if (flash.initialize())
Serial.println("SPI Flash Init OK!");
else
Serial.println("SPI Flash Init FAIL! (is chip present?)");
*/
}
byte ackCount=0;
void loop() {
//process any serial input
if (Serial.available() > 0)
{
char input = Serial.read();
if (input == 'r') //d=dump all register values
radio.readAllRegs();
if (input == 'E') //E=enable encryption
radio.encrypt(ENCRYPTKEY);
if (input == 'e') //e=disable encryption
radio.encrypt(null);
if (input == 'p')
{
promiscuousMode = !promiscuousMode;
radio.promiscuous(promiscuousMode);
Serial.print("Promiscuous mode ");Serial.println(promiscuousMode ? "on" : "off");
}
/*
if (input == 'd') //d=dump flash area
{
Serial.println("Flash content:");
int counter = 0;
while(counter<=256){
Serial.print(flash.readByte(counter++), HEX);
Serial.print('.');
}
while(flash.busy());
Serial.println();
}
*/
/*
if (input == 'D')
{
Serial.print("Deleting Flash chip content... ");
flash.chipErase();
while(flash.busy());
Serial.println("DONE");
}
if (input == 'i')
{
Serial.print("DeviceID: ");
word jedecid = flash.readDeviceId();
Serial.println(jedecid, HEX);
}
*/
if (input == 't')
{
byte temperature = radio.readTemperature(-1); // -1 = user cal factor, adjust for correct ambient
byte fTemp = 1.8 * temperature + 32; // 9/5=1.8
Serial.print( "Radio Temp is ");
Serial.print(temperature);
Serial.print("C, ");
Serial.print(fTemp); //converting to F loses some resolution, obvious when C is on edge between 2 values (ie 26C=78F, 27C=80F)
Serial.println('F');
}
}
if (radio.receiveDone())
{
Serial.print('[');Serial.print(radio.SENDERID, DEC);Serial.print("] ");
if (promiscuousMode)
{
Serial.print("to [");Serial.print(radio.TARGETID, DEC);Serial.print("] ");
}
for (byte i = 0; i < radio.DATALEN; i++)
Serial.print((char)radio.DATA[i]);
Serial.print(" [RX_RSSI:");Serial.print(radio.RSSI);Serial.print("]");
if (radio.ACK_REQUESTED)
{
byte theNodeID = radio.SENDERID;
radio.sendACK();
Serial.print(" - ACK sent.");
// When a node requests an ACK, respond to the ACK
// and also send a packet requesting an ACK (every 3rd one only)
// This way both TX/RX NODE functions are tested on 1 end at the GATEWAY
if (ackCount++%3==0)
{
Serial.print(" Pinging node ");
Serial.print(theNodeID);
Serial.print(" - ACK...");
delay(3); //need this when sending right after reception .. ?
if (radio.sendWithRetry(theNodeID, "ACK TEST", 8, 0)) // 0 = only 1 attempt, no retries
Serial.print("ok!");
else Serial.print("nothing");
}
}
Serial.println();
Blink(LED,3);
}
}
void Blink(byte PIN, int DELAY_MS)
{
pinMode(PIN, OUTPUT);
digitalWrite(PIN,HIGH);
delay(DELAY_MS);
digitalWrite(PIN,LOW);
}