slipstick:
You say readings are currently displayed on serial monitor. It takes code to do that. Where is it?Then you can change it from writing stuff to serial monitor to writing the same stuff to bluetooth via the HM10. There are many examples available showing how to use the HM-10.
Steve
here is my code:
#define PIN_SENSOR1 A1
#define PIN_SENSOR2 A2
#define PIN_SENSOR3 A3
#define PIN_SENSOR4 A4
#define PIN_SENSOR5 A5
#define PIN_HEATER1 11
#define PIN_HEATER2 10
#define PIN_HEATER3 9
#define PIN_HEATER4 6
#define PIN_HEATER5 5
float target = 30;
void setup()
{
pinMode(PIN_SENSOR1, INPUT);
pinMode(PIN_SENSOR2, INPUT);
pinMode(PIN_SENSOR3, INPUT);
pinMode(PIN_SENSOR4, INPUT);
pinMode(PIN_SENSOR5, INPUT);
pinMode(PIN_HEATER1, OUTPUT);
pinMode(PIN_HEATER2, OUTPUT);
pinMode(PIN_HEATER3, OUTPUT);
pinMode(PIN_HEATER4, OUTPUT);
pinMode(PIN_HEATER5, OUTPUT);
Serial.begin(9600);
}
float getTemperature1() {
float data = analogRead(PIN_SENSOR1);
return (5.0 * data * 100.0) / 1024.0;
}
float getTemperature2() {
float data = analogRead(PIN_SENSOR2);
return (5.0 * data * 100.0) / 1024.0;
}
float getTemperature3() {
float data = analogRead(PIN_SENSOR3);
return (5.0 * data * 100.0) / 1024.0;
}
float getTemperature4() {
float data = analogRead(PIN_SENSOR4);
return (5.0 * data * 100.0) / 1024.0;
}
float getTemperature5() {
float data = analogRead(PIN_SENSOR5);
return (5.0 * data * 100.0) / 1024.0;
}
void loop()
{
float c1 = getTemperature1();
Serial.print("Temperature 1 : ");
Serial.println(c1);
if (c1 < target)
{
analogWrite(PIN_HEATER1, 30);
Serial.print("\Heater 1 on");
}else {
digitalWrite(PIN_HEATER1, LOW);
Serial.print("\Heater 1 O-F-F");
}
delay (1000);
float c2 = getTemperature2();
Serial.print("Temperature 2 : ");
Serial.println(c2);
if (c2 < target)
{
analogWrite(PIN_HEATER2, 30);
Serial.print("\Heater 2 on");
}else {
digitalWrite(PIN_HEATER2, LOW);
Serial.print("\Heater 2 O-F-F");
}
delay (1000);
float c3 = getTemperature3();
Serial.print("Temperature 3 : ");
Serial.println(c3);
if (c3 < target)
{
analogWrite(PIN_HEATER3, 30);
Serial.print("\Heater 3 on");
}else {
digitalWrite(PIN_HEATER3, LOW);
Serial.print("\Heater 3 O-F-F");
}
delay (1000);
float c4 = getTemperature4();
Serial.print("Temperature 4 : ");
Serial.println(c4);
if (c4 < target)
{
analogWrite(PIN_HEATER4, 30);
Serial.print("\Heater 4 on");
}else {
digitalWrite(PIN_HEATER4, LOW);
Serial.print("\Heater 4 O-F-F");
}
delay (1000);
float c5 = getTemperature5();
Serial.print("Temperature 5 : ");
Serial.println(c5);
if (c5 < target)
{
analogWrite(PIN_HEATER5, 30);
Serial.print("\Heater 5 on");
}else {
digitalWrite(PIN_HEATER5, LOW);
Serial.print("\Heater 5 O-F-F");
}
delay (1000);
}
now, how can i connect the HM-10 and to see the reading in the application?
thank you very much