I've started to work on a project using EasyVR and Arduino.
I've uploaded this code...
#if defined(ARDUINO) && ARDUINO >= 100
#include "Arduino.h"
#include "SoftwareSerial.h"
SoftwareSerial port(12,13);
#else // Arduino 0022 – use modified NewSoftSerial
#include "WProgram.h"
#include "NewSoftSerial.h"
NewSoftSerial port(12,13);
#endif
#include "EasyVR.h"
EasyVR easyvr(port);
//Groups and Commands
enum Groups
{
//GROUP_0 = 0,
GROUP_1 = 1,
};
enum Group0
{
G0_ARDUINO = 0,
};
enum Group1
{
G1_PLAY = 0,
G1_PAUSE = 1,
G1_PREVIOUS = 2,
G1_NEXT = 3,
G1_STOP = 4,
G1_VOLUME_UP = 5,
G1_VOLUME_DOWN = 6,
G1_MINIMIZE = 7,
G1_MUTE = 8,
G1_FULLSCREEN = 9,
G1_FOCUS_VIDEO = 10,
G1_FOCUS_PHOTO = 11,
G1_CLOSE = 12,
};
EasyVRBridge bridge;
int8_t group, idx;
void setup()
{
// bridge mode?
if (bridge.check())
{
cli();
bridge.loop(0, 1, 12, 13);
}
// run normally
Serial.begin(9600);
port.begin(9600);
if (!easyvr.detect())
{
Serial.println("EasyVR not detected!");
for (;;);
}
easyvr.setPinOutput(EasyVR::IO1, LOW);
Serial.println("EasyVR detected!");
easyvr.setTimeout(5);
easyvr.setLanguage(EasyVR::ENGLISH);
group = EasyVR::TRIGGER; //<– start group (customize)
pinMode(2, OUTPUT);
digitalWrite(2, LOW); // set the LED off
pinMode(3, OUTPUT);
digitalWrite(3, LOW);
pinMode(4, OUTPUT);
digitalWrite(4, LOW);
pinMode(5, OUTPUT);
digitalWrite(5, LOW);
pinMode(6, OUTPUT);
digitalWrite(6, LOW);
}
void action();
void loop()
{
easyvr.setPinOutput(EasyVR::IO1, HIGH); // LED on (listening)
Serial.print("Say a command in Group");
Serial.println(group);
easyvr.recognizeCommand(group);
do
{
// can do some processing while waiting for a spoken command
}
while (!easyvr.hasFinished());
easyvr.setPinOutput(EasyVR::IO1, LOW); // LED off
idx = easyvr.getWord();
if (idx >= 0)
{
// built-in trigger (ROBOT)
// group = GROUP_X; <– jump to another group X
return;
}
idx = easyvr.getCommand();
if (idx >= 0)
{
// print debug message
uint8_t train = 0;
char name[32];
Serial.print("Command: ");
Serial.print(idx);
if (easyvr.dumpCommand(group, idx, name, train))
{
Serial.print(" = ");
Serial.println(name);
}
else
Serial.println();
easyvr.playSound(0, EasyVR::VOL_FULL);
// perform some action
action();
}
else // errors or timeout
{
if (easyvr.isTimeout())
Serial.println("Timed out, try again…");
int16_t err = easyvr.getError();
if (err >= 0)
{
Serial.print("Error ");
Serial.println(err, HEX);
}
group = GROUP_1;
}
}
void action()
{
switch (group)
{
// case GROUP_0:
// switch (idx)
// {
// case G0_ARDUINO:
// write your action code here
// group = GROUP_1; //<– or jump to another group X for composite commands
// break;
// }
// break;
case GROUP_1:
switch (idx)
{
case G1_PLAY:
Serial.print("PLAY");
digitalWrite(2, HIGH);
break;
case G1_PAUSE:
Serial.print("PAUSE");
digitalWrite(3,HIGH);
break;
case G1_PREVIOUS:
Serial.print("PREVIOUS");
digitalWrite(4,HIGH);
break;
case G1_NEXT:
Serial.print("NEXT");
digitalWrite(5,HIGH);
break;
case G1_STOP:
Serial.print("STOP");
digitalWrite(6,HIGH);
break;
/case G1_VOLUME_UP:
Serial.print("INCRESING VOLUME...");
digitalWrite(7,HIGH);
break;
case G1_VOLUME_DOWN:
Serial.print("DECREASING VOLUME...");
digitalWrite(8,HIGH);
break;
case G1_MINIMIZE:
Serial.print("MINIMIZE");
digitalWrite(9,HIGH);
break;
case G1_MUTE:
Serial.print("MUTE");
digitalWrite(10,HIGH);
break;
case G1_FULLSCREEN:
Serial.print("X");
digitalWrite(11,HIGH);
break;/
/case G1_FOCUS_VIDEO:
Serial.print("Y");
digitalWrite(12,HIGH);
break;
case G1_FOCUS_PHOTO:
Serial.print("Z");
digitalWrite(13,HIGH);
break;
case G1_CLOSE:
Serial.print("CLOSE");/
//digitalWrite(13,HIGH);
}
break;
}
}