IR Remote controlled finger for camera shutter (completed with demo video)

This is one of my first completed arduino projects. A IR remote controlled (and also laser controlled) finger to manually press a camera shutter button on a Nikon P100 camera, since that camera has no other way to support remote shutter.

Demo video here. Remote controlled finger. Give any camera remote shutter capability, and laser. - YouTube

I plan to eventually put up some sort of tutorial somewhere for other newbies to help avoid some of the issues I struggled with while learning, if anyone knows a good place to put up a quick and simple tutorial without a bunch of hoops to jump through let me know.

By the way, here is the code.

/* Note, first time run, with no values stored in EEPROM might be a bit buggy, 
as soon as values are stored, will work fine */

#include <IRremote.h>
#include <Servo.h> 
#include <EEPROM.h>
int RECV_PIN = 11;  //ir reciever hooked on pin 11 through 220ohm resistor
Servo myservo;   // create servo object to control a servo

int position1;   //servo position 1
int position2;   //servo position 2
int position3;   //servo position 3
int codeValue;   //the code from the remote
int current;     //keeps track of current servo position

IRrecv irrecv(RECV_PIN);

decode_results results;

void setup()
  position1 =;    //default servo positon 1
  position2 =;   //default servo position 2
  position3 =;  //default servo position 3
  irrecv.enableIRIn(); // Start the receiver
  myservo.attach(9);  // attaches the servo on pin 9
  myservo.write(position1);   //start the servo out at position 1
  current = position1;

void loop() {
  if (irrecv.decode(&results)) {
    codeValue = results.value;
    switch (codeValue) {
    case 16753245:    
      current = position1;
    case 16736925:    
      current = position2;
    case 16769565:    
      current = position3;
    case 16761405:
      ++current;                //moves servo 1 degrees
      if (current > 179) current = 179;  //this makes sure the current variable doesn't exceed the servo range
    case 16748655:
      if (current < 0) current = 0;  //makes sure variable doesn't drop below 0
    case 16712445:
      current += 10;  //moves servo 10 degrees
      if (current > 179) current = 179;
    case 16754775:
      current -= 10;
      if (current < 0) current = 0;
    case 16720605:    
      myservo.write(179);  //moves servo all the way to 179
      current = 179;
    case 16769055:    
      current = 0;
    case 16738455:    
      position1 = current;  //stores current position as servo position 1
      EEPROM.write(1, position1);  //writes position 1 to eeprom address 1
    case 16750695:    
      position2 = current;  //stores current position as servo position 2
      EEPROM.write(2, position2);  //writes position 2 to eeprom address 2
    case 16756815:    
      position3 = current;  //stores current position as servo position 3
      EEPROM.write(3, position3);  //writes position 3 to eeprom  address 3
    case 16724175:    //this is for the laser sensor
      int sensorValue = analogRead(A0);     //cds photocell hooked to analog 0, has 10k pulldown resistor to ground
      while (sensorValue > 950) {              //value can be adjusted, 950 very sensitive for my conditions
        digitalWrite(13, HIGH);        //status light, led on means laser is armed
        sensorValue = analogRead(A0);    //reads sensor value again for the loop
      current = position3;
      digitalWrite(13, LOW);             //turns led off to indicate status that servo was activated.
      delay(1000);                        //delay just for good measure, holds servo for a second
      myservo.write(position1);          //moves servo back to position 1
      current = position1;
irrecv.resume(); // Receive the next value


This would be an optional output choice for this:

Im very new to arduino and was looking for some thing like your project to use with my sony nex-3. I made a "copy paste" of your code but when I try to send the code to my arduino it gives so many errors that I dont know were is the problem !?!?! can you help me?
Ps. the errors ar in the atached file.

erros.txt (8.72 KB)