No access to web portal interface

Hi everyone I'm new here and I haven't quite found an answer to my problem. I've been playing with my new Yun for a couple days now and because of the learning process I've reset the unit by holding the wifi reset button for longer than 30 seconds. This has worked to fix any thing that I may have broken, till tonight.

I can reset like normal which takes me to the access point login and config. Once I finish the config and reboot, I can no longer access the Yun. I don't have a usb cable yet so I can't console in and see what is going on. Has anyone else has this problem? I've read a way to use the IDE to console in and press the f key, go into fail safe and run factory restore. Is this something I may need to do?

Thanks

Can you say exactly what you do during config, that will be the key to solve your problem. Now we are blind.

I do the basic first time config.

  1. I log onto the Yun's wifi
  2. Go to ardruino.local
  3. Login with password arduino
  4. Set name to arduinoyun and set my password
  5. Select my home wifi and enter the password
  6. Save and reboot
  7. Connect to my home network
  8. After the Yun is done booting I click on the "You can fine me here" button which takes me to arduinoyun.local
  9. The link takes me to a redirect screen and then to an error loading sceen. As if a webpage could not be found.

Everything I've done is the same, just now once I get the Yun to connect to my home network I can no longer access it. I also don't see the Yun's IP in my router's connected devices.

UPDATE:

I was able to access through the wired ethernet and my wireless is not connected. some of the log is below (9500 character limit).

[    0.000000] Linux version 3.8.3 (federico@smilzo) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #8 Mon Aug 19 16:22:39 CEST 2013


[    0.700000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    1.250000] eth0: Found an AR7240/AR9330 built-in switch
[    2.280000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.830000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[    2.830000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.840000] ehci-platform: EHCI generic platform driver
[    2.840000] ehci-platform ehci-platform: EHCI Host Controller
[    2.840000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    2.840000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    2.870000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    2.870000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.870000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.870000] usb usb1: Product: EHCI Host Controller
[    2.880000] usb usb1: Manufacturer: Linux 3.8.3 ehci_hcd
[    2.880000] usb usb1: SerialNumber: ehci-platform
[    2.880000] hub 1-0:1.0: USB hub found
[    2.880000] hub 1-0:1.0: 1 port detected
[    2.890000] Initializing USB Mass Storage driver...
[    2.890000] usbcore: registered new interface driver usb-storage
[    2.890000] USB Mass Storage support registered.
[    2.890000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[    2.900000] sdhci: Secure Digital Host Controller Interface driver
[    2.900000] sdhci: Copyright(c) Pierre Ossman
[    2.900000] usbcore: registered new interface driver ushc
[    2.900000] TCP: cubic registered
[    2.900000] NET: Registered protocol family 17
[    2.910000] Bridge firewalling registered
[    2.910000] 8021q: 802.1Q VLAN Support v1.8
[    2.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.920000] Freeing unused kernel memory: 232k freed
[    3.220000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    3.420000] usb 1-1: New USB device found, idVendor=058f, idProduct=6254
[    3.420000] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    3.420000] usb 1-1: Product: USB2.0Hub
[    3.550000] hub 1-1:1.0: USB hub found
[    3.550000] hub 1-1:1.0: 4 ports detected
[    3.990000] usb 1-1.4: new high-speed USB device number 3 using ehci-platform
[    4.230000] usb 1-1.4: New USB device found, idVendor=058f, idProduct=6366
[    4.230000] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    4.230000] usb 1-1.4: Product: Mass Storage Device
[    4.230000] usb 1-1.4: Manufacturer: Generic
[    4.240000] usb 1-1.4: SerialNumber: 058F0O1111B1
[    4.330000] scsi0 : usb-storage 1-1.4:1.0
[    5.290000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[    5.330000] scsi 0:0:0:0: Direct-Access     Multi    Flash Reader     1.00 PQ: 0 ANSI: 0
[    9.840000] jffs2: notice: (528) jffs2_build_xattr_subsystem: complete building xattr subsystem, 4 of xdatum (0 unchecked, 3 orphan) and 68 of xref (0 dead, 56 orphan) found.
[   11.690000] sd 0:0:0:0: [sda] 15523840 512-byte logical blocks: (7.94 GB/7.40 GiB)
[   11.690000] sd 0:0:0:0: [sda] Write Protect is off
[   11.690000] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[   11.690000] sd 0:0:0:0: [sda] No Caching mode page present
[   11.690000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   11.700000] sd 0:0:0:0: [sda] No Caching mode page present
[   11.700000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   11.720000]  sda: sda1
[   11.720000] sd 0:0:0:0: [sda] No Caching mode page present
[   11.730000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   11.730000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   39.150000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[   39.150000] Backport based on wireless-testing.git master-2013-02-22
[   39.150000] compat.git: wireless-testing.git
[   39.190000] cfg80211: Calling CRDA to update world regulatory domain
[   39.190000] cfg80211: World regulatory domain updated:
[   39.190000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   39.190000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   39.200000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   39.200000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   39.200000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   39.210000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   39.990000] ath: EEPROM regdomain: 0x0
[   39.990000] ath: EEPROM indicates default country code should be used
[   39.990000] ath: doing EEPROM country->regdmn map search
[   39.990000] ath: country maps to regdmn code: 0x3a
[   39.990000] ath: Country alpha2 being used: US
[   39.990000] ath: Regpair used: 0x3a
[   39.990000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   40.000000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[   40.010000] cfg80211: Calling CRDA for country: US
[   40.010000] cfg80211: Regulatory domain changed to country: US
[   40.010000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   40.010000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[   40.020000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[   40.020000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   40.020000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   40.030000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   40.030000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[   40.390000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   40.430000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[   40.460000] PPP generic driver version 2.4.2
[   40.610000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   41.040000] NET: Registered protocol family 24
[   41.070000] nf_conntrack version 0.5.0 (955 buckets, 3820 max)
[   41.820000] Linux video capture interface: v2.00
[   42.080000] fuse init (API version 7.20)
[   49.000000] eth1: link up (100Mbps/Full duplex)
[   56.300000] wlan0: authenticate with 08:60:6e:ba:3f:a0
[   56.350000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 1/3)
[   56.460000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 2/3)
[   56.570000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 3/3)
[   56.680000] wlan0: authentication with 08:60:6e:ba:3f:a0 timed out
[   59.280000] wlan0: authenticate with 08:60:6e:ba:3f:a0
[   59.330000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 1/3)
[   59.440000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 2/3)
[   59.550000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 3/3)
[   59.660000] wlan0: authentication with 08:60:6e:ba:3f:a0 timed out
[   62.640000] wlan0: authenticate with 08:60:6e:ba:3f:a0
[   62.690000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 1/3)
[   62.800000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 2/3)
[   62.910000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 3/3)
[   63.020000] wlan0: authentication with 08:60:6e:ba:3f:a0 timed out
[   68.180000] wlan0: authenticate with 08:60:6e:ba:3f:a0
[   68.230000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 1/3)
[   68.340000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 2/3)
[   68.450000] wlan0: direct probe to 08:60:6e:ba:3f:a0 (try 3/3)
[   68.640000] wlan0: authentication with 08:60:6e:ba:3f:a0 timed out/code]

What IP address do you see for WLAN of the yun in the advanced configuration panel ? can you ping this address ?

wlan0 – 192.168.240.1 eth1 – 192.168.1.181

Where I’m at is I did a console factory reset with “./reset-to-factory-anyway”. But it looks like I’m having the same problem. After the reset the Yun acted like normal. I went to Arduino.local and did the basic wifi config, time zone, and password then reset. The blue bar loaded 100%, the Yun rebooted, and the Yun default AP wifi was gone. I was already connected to my home wifi so I went to myyun.local however, just like before the web interface will not load. I tried going to 192.168.1.181 and again nothing.

After a few minutes I noticed that the default Yun AP wifi was back in my wifi list. I didn’t reset the Yun it just showed up after a few minutes. I’m guessing it couldn’t connect to my home wifi so it reverted back to default. Once the Yun was at default AP mode I could access the Yun like normal, I can even SSH using 192.168.1.181. My password is still intact, so I know that it is just resetting the wifi.

What I’m thinking is that I SSH to /etc/config/network and manually enter my home wireless information. I’m not sure what else to do, maybe reload the Atheros kmod-ath9k driver?

can you ping the adresses ? it is not because they appear on screen that you can ping them, ping them to be sure they were given by your router