Not Able to Upload code to Nano

Development Tools IDE 1.x
1

Hi all,

Greetings!!!

I have bought a Nano V3 and there is not a defect when it arrived because I could see the internal LED blinking. Now when I tried to upload inbuilt code to Nano it shows below error

System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"

Using Port : COM1
Using Programmer : arduino
Overriding Baud Rate : 115200
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0xb2
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xb2

avrdude done. Thank you.

Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

Since it was using CH340 chip so I have installed appropriate drivers (CH340 drivers) . Also the com port was also right. Additional Details:

board: 'Arduino Nano'
programmer : 'AVRISP mkll'
processor : ATmega328P

Even I tried to upload the bootloader in nano using working arduino UNO but still no luck.

Please find the attachment for errors

Thanks in advance

Regards
Rahul

Capture_1.PNG
Capture_1.PNG808×562 9.48 KB

2

Select Tools > Processor > ATmega328P (Old Bootloader) and then try uploading again.

3

Hi Pert,

Thank for the reply

I have tried that but still no luck

Regards
Rahul

4

Remove any connections to pins 0 and 1 on your Arduino board. These pins are used for communication with your computer, including uploads. Connecting anything to these pins can interfere with uploads.

Make sure you have the correct board selected from the Tools > Board menu.

Make sure you have selected the port of your Arduino board from the Tools > Port menu.

Sometimes the port will be labeled with the board name in the menu. Other times it will not. If you don’t know which port is your Arduino board, you can find it like this:

  • Unplug your Arduino board from the computer.
  • Tools > Port
  • Note the ports, if any, listed in the menu.
  • Close the Tools menu. The ports list is only updated when the Tools menu is re-opened, so this step is essential.
  • Plug your Arduino board into the computer.
  • Tools > Port - The new port listed in the menu is your Arduino board.