Hello,
I am making an ESC based on arduino platform. This is the schematic I made for the nano part of the ESC:
The LED was left out because I don't really need it on the ESC.
I tried to upload a bootloader with another nano following this tutorial:
http://www.electronoobs.com/eng_arduino_tut6.php
but I always get this error message:
Arduino: 1.8.5 (Windows 10), Board: "Arduino Nano, ATmega328P"
D:\Programs\Installed\Arduino\arduino-1.8.5\hardware\tools\avr/bin/avrdude -CD:\Programs\Installed\Arduino\arduino-1.8.5\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM12 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDA:m -Ulfuse:w:0xFF:m
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "D:\Programs\Installed\Arduino\arduino-1.8.5\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM12
Using Programmer : stk500v1
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500
Description : Atmel STK500 Version 1.x firmware
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.04s
avrdude: Device signature = 0xffffff (probably .reduced_core_tiny) (retrying)
Reading | ################################################## | 100% 0.05s
avrdude: Device signature = 0xffffff (probably .reduced_core_tiny) (retrying)
Reading | ################################################## | 100% 0.04s
avrdude: Device signature = 0xffffff (probably .reduced_core_tiny)
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
avrdude done. Thank you.
Error while burning bootloader.
If anyone has any idea of what could possibly be wrong that would be great.