Problem with using load sensor

Hi , i am trying to use load sensor like this one https://www.sparkfun.com/products/10245. Basically what i had done, i had just dissected a personal weighing scale and removed the load sensor. But got no success in using them with Arduino. I am using INA125P instrumentation amplifier with below configuration. File enclosed with this question

Where S+ and S- are Sense + and Sense -. I tried all the configuration i.e single load cell, half wheat-stone bridge, full weat-stone bridge but nothing worked. I only keep on getting some random ADC value 14-16 and even on pressing the load sensor upside down, nothing changed. Basically i followed the below configuration while trying with single load cell.

I am trying to use a 3 wire load sensor, connect it to INA125 for voltage amplification and then use the amplified output to be fed to ADC of Arduino.

I had used below configuration with INA125. enter image description here

Where S+ and S- are Sense + and Sense -. I tried all the configuration i.e single load cell, half wheat-stone bridge, full weat-stone bridge but nothing worked. I only keep on getting some random ADC value 14-16 and even on pressing the load sensor upside down, nothing changed. Basically i followed the below configuration while trying with single load cell.

And a simple arduino code, just to read ADC value in order to check , whether i am getting things right. As per code, the ADC value must change, but they didn’t. Below is the sample code.

#include<stdio.h>
#include <LiquidCrystal.h>
LiquidCrystal lcd(12, 11, 5, 4, 3, 2);

int sensorValue = 0;
int sensorPin = A0;


void setup()
{

  Serial.begin(9600);
  Serial.println("Weight sensor reading");
  lcd.begin(16, 2);

}

void loop()
{
  lcd.begin(16, 2);
  lcd.setCursor(0,0);
  lcd.print("Weight measurement");
  sensorValue = analogRead(sensorPin);
  Serial.print(sensorValue);
  lcd.setCursor(0,1);
  lcd.print(sensorValue);
  delay(200);
}

Now with respect to the single load cell, i connected black to GND, white to +5V and Red to S+ at pin 6 of INA125 and i connected PIN7 that is S- to GND. But this didn’t worked.

When i used 2 load sensors, i connected the white wires of both load sensors to +5V, Black wire to GND, RED wire of 1st load sensor to S+ and RED wire of other load sensor to S-. But even that didn’t work and readings remain same i.e. 14-16 volts and didn’t change even on applying sufficient amount of pressure.

Now with respect to the full wheat-stone bridge configuration, i used this pic based configuration given on below link.But even it didn’t worked
http://www.nerdkits.com/forum/thread/900/

I am not able to understand what i am doing wrong.Can any one suggest me

Important : I am using 10k resistance between PIN8 an PIN9, which provide me a gain of 10. Is that sufficient for arduino to read ? Or i must use some other resistance which must provide me a higher gain. But i think even with 10k resistance i must see some change in the value of the ADC, but i am not even getting that. In my earlier question also, i asked a similar type of question, but at that time i wasn’t having INA125 with me.Link for the question is given below.

I had enclosed pic for the arrangement which i am using at present named as loadsensorreadings.jpg

Below is the pic for the configuration which i am using.
I had asked a detailed question at stackover flow and repeating that here too.

Earlier i had used 10k resistance for Rg and now with 60ohm but neither of them worked.

Until you get the gain adjusted properly you're going to see one of two results from the InAmp; either ~2V or ~4V.

If it's sitting at the ~2V value then your gain is too low. If it's at the ~4V value then the gain is too high. Keep playing with the gain until you get something in between, then decrease it a few ohms until it shows ~2V... and then you're ready to test it by pushing on the load cell.