Effectivement, ca change tout !
Ca semble bien programmer l'ATmega, j'ai le rapport suivant (je n'ai mis que la deuxième moitié):
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM12
Using Programmer : stk500v1
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : STK500
Description : Atmel STK500 Version 1.x firmware
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.02s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: NOTE: "flash" memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: reading input file "C:\Users\Ludo\AppData\Local\Temp\arduino_build_587003/Blink.ino.hex"
avrdude: writing flash (938 bytes):
Writing | ################################################## | 100% 1.11s
avrdude: 938 bytes of flash written
avrdude: verifying flash memory against C:\Users\Ludo\AppData\Local\Temp\arduino_build_587003/Blink.ino.hex:
avrdude: load data flash data from input file C:\Users\Ludo\AppData\Local\Temp\arduino_build_587003/Blink.ino.hex:
avrdude: input file C:\Users\Ludo\AppData\Local\Temp\arduino_build_587003/Blink.ino.hex contains 938 bytes
avrdude: reading on-chip flash data:
Reading | ################################################## | 100% 0.63s
avrdude: verifying ...
avrdude: 938 bytes of flash verified
avrdude done. Thank you.
Mais finalement, il m'est impossible de faire clignoter une led. Elle fonctionne correctement (et est dans le bon sens), anode vers le pin 13 derrière une résistance de 470ohms, cathode sur la masse.
Comment être certain que l'ATmega est bien chargé !!?
Merci encore