I just got my first new Arduino UNO today and I tried to upload some blinking code on it. I noticed that teh LEDs on RX and TX are not on and I get this error when uploading code
Sketch uses 940 bytes (2%) of program storage space. Maximum is 32256 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 2039 bytes for local variables. Maximum is 2048 bytes.
C:\Users\soran\Downloads\arduino-nightly\hardware\tools\avr/bin/avrdude -CC:\Users\soran\Downloads\arduino-nightly\hardware\tools\avr/etc/avrdude.conf -v -patmega328p -carduino -PCOM3 -b115200 -D -Uflash:w:C:\Users\soran\AppData\Local\Temp\arduino_build_829957/sketch_dec26a.ino.hex:i
avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch
System wide configuration file is "C:\Users\soran\Downloads\arduino-nightly\hardware\tools\avr/etc/avrdude.conf"
Using Port : COM3
Using Programmer : arduino
Overriding Baud Rate : 115200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
Programmer Type : Arduino
Description : Arduino
Hardware Version: 3
Firmware Version: 4.4
Vtarget : 0.3 V
Varef : 0.3 V
Oscillator : 28.800 kHz
SCK period : 3.3 us
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x1e950f (probably m328p)
avrdude: reading input file "C:\Users\soran\AppData\Local\Temp\arduino_build_829957/sketch_dec26a.ino.hex"
avrdude: writing flash (940 bytes):
Writing | ################################################## | 100% 0.16s
avrdude: 940 bytes of flash written
avrdude: verifying flash memory against C:\Users\soran\AppData\Local\Temp\arduino_build_829957/sketch_dec26a.ino.hex:
avrdude: load data flash data from input file C:\Users\soran\AppData\Local\Temp\arduino_build_829957/sketch_dec26a.ino.hex:
avrdude: input file C:\Users\soran\AppData\Local\Temp\arduino_build_829957/sketch_dec26a.ino.hex contains 940 bytes
avrdude: reading on-chip flash data:
Reading | ###############################Invalid library found in C:\Users\soran\Documents\Arduino\libraries\sketch_dec26a: C:\Users\soran\Documents\Arduino\libraries\sketch_dec26a
Invalid library found in C:\Users\soran\Documents\Arduino\libraries\sketch_dec26a: C:\Users\soran\Documents\Arduino\libraries\sketch_dec26a
################### | 100% 0.14s
avrdude: verifying ...
avrdude: 940 bytes of flash verified
avrdude done. Thank you.
I am not sure what any of this means and I would greatly appreciate any help at all.