Sketch Fehlermeldung...

International Deutsch
4

Hallo,
also ich habe hier auch die Version 1.0 und die Fehlermeldung bezieht sich auf Zeile 4.
Zumindest wird die nach dem Klick auf Verify makiert.

// Data wire is plugged into port 2 on the Arduino

Und der Ordner mit den Libraries befindet sich hier : arduino-1.0\libraries
Dort heist der Ordner DallasTemperatur.

Sollte die defekt sein, wo kriege ich denn eine Funktionierende her ?
Vieleicht von dir uwefed ? :wink:

Es werden aber noch eine Menge anderer Fehler ausgeworfen, in dem unterem Feld.
Das folgende steht im unterem Feld:

sketch_mar28a:3: error: variable or field 'printAddress' declared void
sketch_mar28a:3: error: 'DeviceAddress' was not declared in this scope
sketch_mar28a:4: error: variable or field 'printTemperature' declared void
sketch_mar28a:4: error: 'DeviceAddress' was not declared in this scope
sketch_mar28a:5: error: variable or field 'printResolution' declared void
sketch_mar28a:5: error: 'DeviceAddress' was not declared in this scope
sketch_mar28a:6: error: variable or field 'printData' declared void
sketch_mar28a:6: error: 'DeviceAddress' was not declared in this scope
sketch_mar28a:11: error: no matching function for call to 'DallasTemperature::DallasTemperature(OneWire*)'
C:\Dokumente und Einstellungen\SONY\Eigene Dateien\Downloads\arduino-1.0-windows\arduino-1.0\libraries\DallasTemperature/DallasTemperature.h:63: note: candidates are: DallasTemperature::DallasTemperature(StratBase*)
C:\Dokumente und Einstellungen\SONY\Eigene Dateien\Downloads\arduino-1.0-windows\arduino-1.0\libraries\DallasTemperature/DallasTemperature.h:38: note:                 DallasTemperature::DallasTemperature(const DallasTemperature&)
sketch_mar28a:16: error: 'DeviceAddress' does not name a type
sketch_mar28a.cpp: In function 'void setup()':
sketch_mar28a:25: error: no matching function for call to 'DallasTemperature::begin()'
C:\Dokumente und Einstellungen\SONY\Eigene Dateien\Downloads\arduino-1.0-windows\arduino-1.0\libraries\DallasTemperature/DallasTemperature.h:69: note: candidates are: void DallasTemperature::begin(uint8_t)
C:\Dokumente und Einstellungen\SONY\Eigene Dateien\Downloads\arduino-1.0-windows\arduino-1.0\libraries\DallasTemperature/DallasTemperature.h:78: note:                 void DallasTemperature::begin(NewOneWire&)
sketch_mar28a:27: error: 'class DallasTemperature' has no member named 'getDeviceCount'
sketch_mar28a:32: error: 'class DallasTemperature' has no member named 'getDeviceCount'
sketch_mar28a:37: error: 'class DallasTemperature' has no member named 'isParasitePowerMode'
sketch_mar28a:40: error: 'DeviceAddress' was not declared in this scope
sketch_mar28a:40: error: expected `;' before 'insideThermometer'
sketch_mar28a:44: error: 'insideThermometer' was not declared in this scope
sketch_mar28a:44: error: 'printAddress' was not declared in this scope
sketch_mar28a:48: error: 'class DallasTemperature' has no member named 'setResolution'
sketch_mar28a:51: error: 'class DallasTemperature' has no member named 'getResolution'
sketch_mar28a.cpp: At global scope:
sketch_mar28a:56: error: variable or field 'printAddress' declared void
sketch_mar28a:56: error: 'DeviceAddress' was not declared in this scope

Was ich nicht verstehe, wieso läuft die bei dir durch (uwefed), hast du den 1zu1 kopiert ?

Vielen Dank für Eure Hilfe...

Greatz
Cetax